Showing Results for "stop+valves"

Customer Reviews

13 Customer Reviews
Single Handle Tub and Shower Pressure Balance Valve with Screwdriver Stops in Rough Brass

It works, looks great, and preforms wonderful!! Very satisfied with product and price was very economical!! It looks great in my new renovated bathroom shower!!

1/2 in. Push-Fit x 1/2 in. Comp Quarter-Turn Angle Stop Valve

I purchased these items online, based on the recommendation from my local Home Depot, to use in hooking up a double sink vanity in my bathroom. However, I've had the local home depot recommend 3 different sets of connecting lines and none of them work on the Compression angle stop valve and they all leaked. So today I need to remove each of these valves and get different valves to complete my bathroom remodel project. I'm really disappointed in the advice I'm receiving from my local Home Depot!

1/2 in. Push-Fit x 1/4 in. OD Comp Quarter-Turn Angle Stop Valve

My valve under my bathroom sink started leaking. It was actually the nut that was made on the copper tubing that had cracked (see picture). I had enough 1/2 copper pipe sticking out the wall were I didn't have to cut any wall out. this was about 7 at night so I didn't want to start soldering pipe. I found this. the guy at home depot was very helpful in showing me how it works. I cleaned up the end of the pipe and pushed this on. turned the water on right away and no leaks. I love this and wish I would have found it sooner or invented it. it is a little more expensive but for what you're getting it is very worth it.

1/4 in. x 3/8 in. Brass Push-Fit x Compression Stop Valve Connector

I used this SharkBite 1/4" Push-Fit x Compression elbow to run PEX from a Undersink Water Filtration unit to the existing compression line. It was easy to install, threaded the nut onto the Male x Male compression adapter and pushed in the 1/4" PEX Pipe.

1/2 in. Solid Brass Slip Stop and Waste Valve

Great valve, well built, and won't break the bank. Understand there is a flow restriction with this valve design, just look down the valve body. Just keep that in mind. Next people time after time do not the perform necessary maintenance on them. After about 5 years, one needs to replace the valve seal, stem packing, and brass side drain.

Valve Check Stop Kit

I ordered a shower valve replacement part and it fit perfectly and was easy to install. My shower valve works fine after an easy installation

1/2 in. Barb x 3/8 in. Compression Quarter-Turn Angle Stop Valve

Gotta love quarter turn shutoff valves. Bought two valves in store and they were stiff but watertight. Nice finish. The valves I purchase had a chrome finish oval handle, not the stubby, but stylish, lever shown in the catalog photo.

1/2 in. Push-Fit x 3/8 in. OD Compression Quarter-Turn Straight Stop Valve

The SharkBite 1/2" x 3/8 Compression valve is very easy to install. I used it to replace an existing compression stop valve, after shutting off water and removing existing stop valve and deburring copper pipe you simply push on the sharkbite shutoff connect the supply line and thats it! No leaks and chrome finish looks great.

Single Handle Pressure Balance Mixing Valve with Screwdriver Stops and Diverter in Rough Brass

After $200 additional in plumber's fee to investigate the problem with the Danze shower system after it had been installed, it was discovered that one of the valve controls was defective. The most efficient way to solve the issue was to buy a second mixing valve and swap out the defective part, and return the mixing valve with the defective piece inserted. Crazy. The only thing that saved the expereince from being too difficult is Home Depot's good customer service. Overall, I cannot recommend Danze fixtures. They look good but the craftsmanship is not there. Buy a more established brand.

1/2 in. Push-Fit x 1/4 in. OD Comp Quarter-Turn Straight Stop Valve

Although I am fairly adept at soldering copper joints, SharkBite fittings make an otherwise complicated job simple. For a quick and easy replacement of a seized up valve, this is perfect, as long as the pipe stub is long enough (it doesn't take too much), clean and not burred.

1/2 in. Brass Slip Stop Valve

OK valve but the washers deteriorate over time. What size is the washer ? BTW- Would a ball valve be a better choice ?

1/2 in. Push-Fit x 3/8 in. OD Compression Quarter-Turn Angle Stop Valve

The SharkBite 1/2" x 3/8 Compression valve is very easy to install. I used it to replace an existing compression stop valve, after shutting off water and removing existing stop valve and deburring copper pipe you simply push on the sharkbite shutoff connect the supply line and thats it! No leaks and chrome finish looks great.

Single Handle 4-Port Shower Diverter Valve with Stops in Rough Brass

I love the feel. The valve has solid ceramic parts inside, very smooth action, and a click-in-place feature that leaves no guessing. The Danze trim for this valve is heavily made and fit together better than anything I have used previously. The other review complained about availability of the trim. I found it easily. There are fancy trim options, about $150 to $250, but the simple trim for the on/off valve (~$90 to $110) also fits this valve. I used the less expensive trim option which I think looks even better than the larger diverter trim with the port markings. This also worked better for me as I wished to use a non-standard port arrangement as I was configuring a "double" shower with one set of body sprays.