Rated 1.8 out of 5 by 9
Rated 4.0 out of 5.0 by DIY609 Looks great
I read the reviews when ordering but felt i didn't have much choice. I replaced 86 balusters
requiring 172 shoes- angled and square. I found that by creating a small wedge from heavy stock paper cut into 1/2" x 1/2" strips and folded and placing this wedge opposite the set screw did the trick. When the set screw was snugged the wedge prevented the tweaking and gaps i read about. Takes a while and the use of needle nose pliers helps with placing the wedge- but all 86 of my top shoes are perfect and look great. Should modifications like this be necessary when you buy a product? No, But given the alternative of no shoe, a crooked shoe or a perfect fitting shoe - the time and no cost fix is worth it when your done. No grinding required.
August 31, 2015
Rated 1.0 out of 5.0 by Michael Poor design left a nice project wanting
As most other people have indicated, the ugly gap between the railing and the shoe detracts significantly from this project. Stair cases are at 42 degree angles whereas these are cut at 45 degrees. To an untrained eye, probably ok. But to someone who 'cares about the details', this is pretty unacceptable. Poor , poor design. Better off not having these in the first place..looks almost as nice.
December 21, 2015
Rated 1.0 out of 5.0 by neverhappy Too bad, product had potential, but the design engineer blew it!
As others have said, the set screw changes the angle and creates a ugly gap. if your not going to design a precision hole, then at least offer two set screws (one on each side) to allow for angle correction. very disappointing to say the least. (Made in China). I would have paid twice this to have a properly designed product. Now I have three choices. Shim it, remove it or leave it as is. Well, I can tell you option #3 will not be being perused.
November 25, 2015
Rated 1.0 out of 5.0 by RA07 Terrible design
The design of the angled baluster shoe is awful. Tightening the screws causes the shoe to bow up on some of them, but not all. Change the design so the screw come in on the side, not the front. Some installed easily, others needed shims to keep it straight. You couldn't tell by looking at them which would work and which wouldn't. To finish your job, order twice as many as you need and pray you get lucky. Out of the 24 I needed, 10 installed easily and 14 needed a lot of extra work.
May 5, 2015
Rated 1.0 out of 5.0 by Skip Poor quality
Baluster shoes are poorly made. Hex (Allen) set screws are not consistent in size. Requires three different allen tools. Also when tightening set screws the shoe torques sideways leaving a large gap between shoe and wood rail and/or base plate.
February 3, 2015
Rated 5.0 out of 5.0 by Jaye Easy to install
We decided to redo our stair rail...easy to install, price was better online than in store....we were going to use them only on the bottom, however decide to place them on the top also...2nd order came fast...we finished the whole project quicky...i love the transformation of the stair case
April 30, 2014
Rated 1.0 out of 5.0 by Cooper Poor Design
I was required to glue the part on the the entire banister in place because the set screws forces the angled part away from the rail and creates a 1/4" gap. Just a poor and cheap design on the manufacturers behalf. They should have put the screw on an angle like the parts Home Depot carried 1 year ago.
February 15, 2014
Rated 1.0 out of 5.0 by ToDoList82 Poor Design
Placement of the set screw causes the shoe to pull away from the banister leaving an ugly gap. Recommend picking up a tube of black adhesive caulk and gluing in place, skip the set screws all together.
May 5, 2014