0077680231918

AFC Cable Systems

Model 8028

Internet #202286682

Store SKU #163112

1/2 in. x 6 ft. Non-Metallic Liquidtight Whip

$8.07 /each
  • Maximum Voltage Rating of 600V
  • RoHS Compliant
  • Maximum dry temp 90 Degrees C and maximum wet temp 75 Degrees C

Frequently Bought Together

Product Overview

The AFC Cable Systems 1/2 in. x 6 ft. Liquidtite Whip comes with 1 straight non-metallic liquid-tight connector and one 90-degree angle non-metallic liquid-tight connector. This whip is 6 ft. L and comes pre-assembled in a 1/2 in. trade size.

  • 6 ft. in length
  • 1 straight, non-metallic liquid-tight connector and one 90-degree angle non-metallic liquid-tight connector
  • Pre-assembled in a 1/2 in. trade size
  • Black, red and green THHN/THWN conductors
  • Note: product may vary by store

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

5 Questions8 Answers

Customer Questions & Answers

1/2 in. x 6 ft. Non-Metallic Liquidtight Whip
1/2 in. x 6 ft. Non-Metallic Liquidtight Whip

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
2 answers

Can I run 12/2 romex in this to an external disconnect switch on the side of my house to feed a 20 amp GFI outlet

This question is from 1/2 in. x 6 ft. Non-Metallic Liquidtight Whip
Asked by
Connecticut
Read all my Q&A
April 25, 2016
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
Stockton, ca
Read all my Q&A
Home Improvement Profile: DIYer
July 10, 2016
Answer: 
Yes you can.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Read all my Q&A
April 26, 2016
Answer: 
The local electrical code should be consulted for the proper wiring installation.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
2 answers

Does the wire in this support 10-2 wire? I'm installing a heater in my garage and want to run this from disconnect.

This question is from 1/2 in. x 6 ft. Non-Metallic Liquidtight Whip
Asked by
Read all my Q&A
March 30, 2016
Want to know if I can just run this from disconnect to heater. I'll be installing 10-2 on 30 amp breaker
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
Stockton, ca
Read all my Q&A
Home Improvement Profile: DIYer
July 10, 2016
Answer: 
Yes it will support 10-2 wire. They also make this in 3/4 if you need a larger diameter.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Read all my Q&A
April 1, 2016
Answer: 
HD Sku # 229541 / Internet # 202286686 / AFC # 8015-HD uses three 10 gauge stranded wires. Thank you!
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
2 answers

when I insert the fittings into the ends do I have to glue them or just push them in?

This question is from 1/2 in. x 6 ft. Non-Metallic Liquidtight Whip
Asked by
Read all my Q&A
June 14, 2014
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
Stockton, ca
Read all my Q&A
Home Improvement Profile: DIYer
July 10, 2016
Answer: 
No there is no glue needed for these fittings. They are more like compression fittings. Simply insert the end into the fitting and tighten down the nut. They hold very strong and are water tight with no glue needed.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Atlanta, GA
Read all my Q&A
Home Improvement Profile: Professional
June 16, 2014
Answer: 
You do not need to glue the fittings and they are pushed directly into the conduit.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
1 answer

Can this be used on an electric hot water heater. 30 gallon - Tall-boy.?

This question is from 1/2 in. x 6 ft. Non-Metallic Liquidtight Whip
Asked by
VT
Read all my Q&A
June 21, 2016
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answer (1)

June 22, 2016
Answer: 
Check with local codes to see if you can use it on your heater.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
2 »
  • 2016-08-17 T12:30:07.203-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_202286682, prod, sort_default
2 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 105ms
  • QUESTIONS, PRODUCT

Customer Reviews

Rated 5.0 out of 5 by 1 reviewer.
Rated 5.0 out of 5.0 by Great indoor/outdoor solution for quick electrical runs. Worked great for my needs. Wanted to add an additional 20 amp outlet on its on circuit to the sub panel I have installed in my garage. The outlet was a very short run from the sub panel. Only about 3 feet. So instead of fumbling around purchasing conduit, connections, and the elbows that I would have needed. I decided to give this a try. Awesome! Awesome! Awesome. Is what I have to say about it. Makes surface mounted electrical run a lot easier. This stuff can latterly be bent beyond a 90 degree angle with out kinking. So there isnt much need for elbows because of the flexibility of the material. It can be easily cut with a razor blade to the length you need. The connections hold very strong. They go on easily and they truly are water tight. Great non metallic solution for quick electrical runs both indoor and outdoor. July 10, 2016
  • 2016-08-20 T11:36:20.195-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_1, tr_1
  • loc_en_US, sid_202286682, prod, sort_default
1-1 of 1
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 54ms
  • REVIEWS, PRODUCT