Model # 8028

Internet #202286682

Store SKU #163112

AFC Cable Systems 1/2 x 6 ft. Non-Metallic Liquidtight Whip
0077680231918

AFC Cable Systems

1/2 x 6 ft. Non-Metallic Liquidtight Whip

  • Maximum Voltage Rating of 600V
  • RoHS Compliant
  • Maximum dry temp 90 Degrees C and maximum wet temp 75 Degrees C
$817 /each

Frequently Bought Together

Product Overview

The AFC Cable Systems 1/2 in. x 6 ft. Liquidtite Whip comes with 1 straight non-metallic liquid-tight connector and one 90-degree angle non-metallic liquid-tight connector. This whip is 6 ft. L and comes pre-assembled in a 1/2 in. trade size.

  • 6 ft. in length
  • 1 straight, non-metallic liquid-tight connector and one 90-degree angle non-metallic liquid-tight connector
  • Pre-assembled in a 1/2 in. trade size
  • Compatible with black, red and green THHN/THWN conductors (not included)
  • Note: product may vary by store

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

Can I run 12/2 romex in this to an external disconnect switch on the side of my house to feed a 20 amp GFI outlet

Asked by: Jeff
NEC says no and here is why. Romex should never be installed into any form of conduit because the insulation on romex is designed to protect the insulated wire inside yet release the proper amount of heat from the wires. Encasing the romex in a conduit will trap in the heat and eventually lead to failure. Dan F
Answered by: sharkeyfinn1
Date published: 2017-06-23

Does the wire in this support 10-2 wire? I'm installing a heater in my garage and want to run this from disconnect.

Want to know if I can just run this from disconnect to heater. I'll be installing 10-2 on 30 amp breaker
Asked by: Designguy84
this one is supplied with 12-2 which is a smaller gauge of wire. Buy the whip that comes with 10-2 just a couple bucks more.
Answered by: sharkeyfinn1
Date published: 2017-03-26

when I insert the fittings into the ends do I have to glue them or just push them in?

Asked by: nick
No there is no glue needed for these fittings. They are more like compression fittings. Simply insert the end into the fitting and tighten down the nut. They hold very strong and are water tight with no glue needed.
Answered by: diversity210
Date published: 2016-07-11

Is the tube UV resistant so that it can be used outdoors?

Asked by: BPerry
Yes, this is approved for Outdoor applications including direct burial, Rated for concrete embedment and Sunlight and oil resistant
Answered by: AFCSupport
Date published: 2017-02-24
  • y_2017, m_6, d_25, h_9CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_, sid_202286682, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 154ms
  • QUESTIONS, PRODUCT

Customer Reviews

1/2 x 6 ft. Non-Metallic Liquidtight Whip is rated 3.0 out of 5 by 2.
Rated 1 out of 5 by from Product Overview below this product says Black, red and green THHN/THWN Conductors NO, this is in... Product Overview below this product says Black, red and green THHN/THWN Conductors NO, this is incorrect. Conductors are not included. You can run romex or THHN, but not included.
Date published: 2017-06-13
Rated 5 out of 5 by from Great indoor/outdoor solution for quick electrical runs. Worked great for my needs. Wanted to add an additional 20 amp outlet on its on circuit to the sub panel I have installed in my garage. The outlet was a very short run from the sub panel. Only about 3 feet. So instead of fumbling around purchasing conduit, connections, and the elbows that I would have needed. I decided to give this a try. Awesome! Awesome! Awesome. Is what I have to say about it. Makes surface mounted electrical run a lot easier. This stuff can latterly be bent beyond a 90 degree angle with out kinking. So there isnt much need for elbows because of the flexibility of the material. It can be easily cut with a razor blade to the length you need. The connections hold very strong. They go on easily and they truly are water tight. Great non metallic solution for quick electrical runs both indoor and outdoor.
Date published: 2016-07-10
  • y_2017, m_6, d_25, h_11
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_, sid_202286682, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 152ms
  • REVIEWS, PRODUCT