Rated 4.2 out of 5 by 13
Rated 5.0 out of 5.0 by BBRG Worked Better than expected
I used the product to strip several layers of paint off an old aluminium trailer. Most of the paint came off with one application. it is important to "let the stripper work for you". I applied as instructed and rehydrated the applied areas with a spray bottle of water every 20 minutes or so, leaving it on for at least 2 hours.....sun baked areas have been more troublesome, but overall it was well worth it.
September 28, 2016
Rated 5.0 out of 5.0 by Zane Does what it says.
Aqua strip works just like it says it does. Used it on my speed boat to remove unwanted paint from gelcoat that previous owner added. Works best in the temperature & times that are on the instructions. Hot days of 90+ degrees and direct sun light don't work so well just like the instructions say, stripper dries out to quick in the heat. Most of my stripping was done in 80-85 degree weather and partial cloudy skies. The can says it should work in 15 minutes to 4 hours, the Aqua strip started bubbling paint in anywhere from 15 minutes to one hour. The thinner the paint, the quicker the time. In places where the paint was thick and had primer underneath, it took one coat to remove paint and some primer, and a second coat to remove the remaining primer. Took less than a half gallon to strip 18' low profile Tahiti Tiger down to original gelcoat. Not sure how it works in other parts of the country, I live in Colorado at 6200 ft., temperature is warm to hot, and dry for the most part.
August 2, 2016
Rated 3.0 out of 5.0 by Coach NOT AS ADVERTISED
The selling point for this product was that it would remove several layers of bottom paint with one application. On 3 layers of bottom paint it has barely gotten through the 1st layer. In order to get through 3 layers on a small portion of the hull, it took 5 applications with scraping in between applications.
I am going to try another product and would like my money back.
May 3, 2016
Rated 5.0 out of 5.0 by WhalerFan Aqua Strip Remover
Used it to strip 3 layers of bottom paint off a 15-foot Boston Whaler. Took 2 gallons. Outstanding results! Took off all the paint, just let it sit and let the chemicals do the work. Gel coat shine was left in tact.
April 4, 2016
Rated 5.0 out of 5.0 by DavidL Awesome stuff
Works as promised. Had several layers of old bottom paint on a fiberglass boat. Put it on thick with a roller, misted it to keep it wet since it was almost 100 degrees out. Waited about 4 hours. Scraped it off with a plastic scraper. Took all but a thin base coat off. Wetsanded with 1000 grit paper and buffed. Looks like new figerglass.
September 1, 2015
Rated 4.0 out of 5.0 by Dutch Good Stripper
I bought an old with really bad paint on the bottom. Like the side of a stucco house and falling off in spots. Aquastrip did the job pretty well but it takes a long time. Hours. Depending on the weather you may need to leave it on overnight. I tried Captain Lee's fiberglass stripper but it seems to raise the gelcoat where it comes in contact with it. I also tried regular methylene chloride.., Both work faster than aquastrip but not really any better. They are also much messier to work with. You have to order it by the gallon online from Home Depot and they have the best price. Delivery usually takes two to three days, not the 6-10 days they quote you. I ordered three times with same delivery results.
June 26, 2014
Rated 3.0 out of 5.0 by John NOT ALL ITS CRACKED UP TO BE
Bought some online as HD had the best price. Had also purchased 1 gallon from west marine. Same exact product. In all cases the gallon size was like a big glob of jello. Unable to brush on easily. I had to place a glob on a brush with my hand and then spread it out. It spread pretty easily. Waited about 2 hours and then started scraping. It didn't go all the way down to the gel coat but only took off one layer of anti fouling paint. I probably have five to seven layers of heavy old paint on my hull. It would only take off the top layer. Lots of scraping required. It will take another 2-3 gallons to finish the job and many many hours. Probably more cost efficient to get the hull soda blasted by a pro right from the get go.
July 5, 2014
Rated 3.0 out of 5.0 by 1a2b3c It didn't do the job as well as expected.
The product was asked to remove multiple applications of paint that were installed over a twenty year period. The produce was applied as directed. Removal was tried one, two, four, and twenty-four hours after application. In all instances it partially removed most of the paint, but not all of the paint. The end result was a spotty 90% removal. Full removal was obtained after sanding with 320 grit wet sand paper. Not having tried other products, I have no plane of reference on its adequacy.
May 29, 2013