Rated 3.4 out of 5 by 19
Rated 5.0 out of 5.0 by eeewee Great Blade
This blade fit perfectly on my yellow AC operated angle grinder perfectly. I made about 10 cuts through some hardened steel with it and it cut through like a hot knife through butter! When I finished, the blade did not show any noticeable wear. this blade is exactly what I was looking for and did the job nicely! Blade is very thin, kerf refers to the thickness, so if that is important, this is your blade. If you need to cut metal, this is the blade for you!!
October 10, 2016
Rated 5.0 out of 5.0 by manchester Dremel and blades cut thru anything!
My son had a dremel and absolutely loves it.....so had to buy one for myself and a set of blades for he and I. Such a versatile tool especially in tight spots. Cuts thru anything.
September 20, 2016
Rated 5.0 out of 5.0 by Keith THIN KERF METAL CUTTER
This is a 4 1/2" Avanti PRO metal cutoff wheel with a 7/8" arbor hole (most common size for 4 1/2" angle grinder). As the name suggests it is for cutting metal. It can handle a maximum 13,280 RPM which is higher than most single speed angle grinders. It makes quick work of cutting through and slotting pipe or sheet metal or even angle iron. This is a very thin 1/16th" wheel for a thin kerf and it also cuts faster than a thicker wheel would. The one drawback of a thin wheel like this is it will wear out faster. However, as you can see in the video, you barely tell it was used after cutting through the 1/2" conduit a couple of times so you will get several cuts with it before it does wear out. Keep in mind that when a wheel is used numerous times it becomes brittle and therefore could crack and shatter (not good if your using it at the time). When it starts looking worn put a new one on.
August 24, 2016
Rated 3.0 out of 5.0 by RJJ21 It works but cuts slowly
I used the Avanti Thin Kerf Metal Cut-Off Disc to cut through a few 1/2 inch bolts and some angle iron. While it did complete the cuts and I did not experience any failures of the product, I did find that it cut slower than products by other manufacturers. The disk fit my 4-1/2 inch angle grinder with no problems and was held securely in the grinder hub mechanism.
January 4, 2016
Rated 5.0 out of 5.0 by MikeLikesIt 4 1/2 Cut-OFf Dis
This disc is made for cutting metal using a angle grinders. It's made of Aluminum oxide formulation for super fast material removal. When cutting several pieces on 1/2" and 3/4" angle iron, it didn't take much effort to cut through it. It didn't use a lot of the dics so it does last long the the cheap one you buy at other stores. The discs is only 1/16" thick so you don't waste a lot of material cutting the pieces. Maximum RPM is 13,280. Overall I am happy with the product.
August 4, 2016
Rated 4.0 out of 5.0 by MadDog Cutting Remarks
With no major projects on the "to-do" list involving cutting of steel, but anxious to try out this cutting disk, I cut a number of slots in a piece of steel channel to evaluate its performance compared to my usual cutting disk. While installing the disk, it felt a little "looser" on the arbor and, when measured, the hole was about 0.001 inch larger than my usual disk, however, it did not appear to affect the operation or accuracy of the disk when cutting. I did note that it cuts a little slower than I am used to for similar disks and tended to leave "burn" marks and slag on the back side of the cut. For normal cutting this will not be a problem. If you are making small, finely detailed pieces as, for example, a sculpture, additional clean up of the cut edges may be necessary. Wear rate of the disk did not seem out of the expected range (this will vary with the type and thickness of material as well as how much "finesse" you use when cutting...not forcing the disk, but finding its "sweetspot").
February 27, 2016
Rated 5.0 out of 5.0 by Mark Solid Performance
You can't go wrong with this blade if you need cutting power for almost any metal. The first thing I used it for was to trim an I-beam in my house to allow trim boards to better fit. It cut very well and diddn't completely wear down like some other blades I've had. And steel is super hard, so cutting copper or rebar or fencing should be a snap. Highly recommended.
August 4, 2016
Rated 4.0 out of 5.0 by Verified Reviewer Works well
We don't own a torch, so we use these little wheels a lot. They work hard to perform for us. We recently cut the tops off of metal fence posts to make a decorative fence around some new plantings in our yard. One of these did the whole job and there is plenty of disc left for the next project. These go onto a little angle grinder perfectly. Very pleased!
July 12, 2016