Model HC2302

Internet #100176073

Store SKU #156254

5/32 in. x 3-1/2 in. x 6-1/2 in. SDS-Plus TC Hex Hammer Drill Bit

$8.97 /each

Frequently Bought Together

Product Overview

Bosch HC2302 SDS-plus Shank Bit (CT) 5/32 in. x 4 in. x 7 in. Tap-con Hex. Bosch Power Tools and Accessories is one of the divisions within the Robert Bosch Tool Corporation, which is one of the largest power tool and accessory manufacturers in the world. Bosch provides a complete line of corded and cordless power tools and accessories engineered to survive any jobsite and allow professionals to take control of their work. Bosch HC2302 SDS-plus Shank Bit (CT) 5/32 in. x 4 in. x 7 in. Tap-con Hex Features: For use with Tap-con/Condrive systems. Hex drive on bit fits into driver sleeve SDS-plus S4 Tap-con Hex Rotary Hammer Bits Item # HC2302 Diameter 5/32 in. Useable Length 4 in. Overall Length 7 in.

  • Accurate, reliable drilling results
  • Carbide construction
  • 2-cutter carbide tip for small diameter holes
  • Centric tip for precise, rounded holes
  • 4 flutes for fast dust extraction

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.




Warranty / Certifications

More Products With These Features


Customer Questions & Answers

1 Question1 Answer

Customer Questions & Answers

5/32 in. x 3-1/2 in. x 6-1/2 in. SDS-Plus TC Hex Hammer Drill Bit
5/32 in. x 3-1/2 in. x 6-1/2 in. SDS-Plus TC Hex Hammer Drill Bit

Ask your questions. Share your answers.

Clear Search Term
1 answer

Is this bit compatible with the Condrive 500 installation tool?

This question is from 3/16 in. x 3-1/2 in. x 6-1/2 in. SDS-Plus TC Hex Hammer Drill Bit
Asked by
Chicago, IL
Read all my Q&A
October 17, 2015
I recently purchased this bit because in the Home Depot product overview, it said "For use with tap-con condrive systems". When I tried to attach the condrive tool over the bit, neither end seemed to securely fit. The 3/16 inch side of the condrive tool didn't fit at all. The 1/4 inch side of the condrive tool fit over the bit but didn't snap on, it would fall off if I pointed the drill downward. Is there some additional attachment that is needed, or did I buy the wrong product (bit) for the tap-con condrive system I have have?
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answer (1)

Asked by
Read all my Q&A
October 19, 2015
Thank you for your question. The Bosch HC2312 is designed for use with masonry fastening systems with hex sleeve drive tools. The hex drive on the bit fits into the driver sleeve. If your installation tool is not 1/4" hex it will not fit properly on this bit.
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
1 of 1
  • 2016-09-07 T13:12:35.286-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_100176073, prod, sort_default
1 of 1
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 35ms

Customer Reviews

Rated 3.1 out of 5 by 9 reviewers.
Rated 1.0 out of 5.0 by LOW QUALITY I had to drill through 1-3/4" concrete . It took me 4 days and purchasing another Bosch masonry bit to complete my task. June 28, 2016
Rated 3.0 out of 5.0 by Adequate bit.... I had a bunch of holes to drill and decided to try this bit. It works, but not overly well. It seems to dull more slowly than the cheaper bits, but also doesn't drill as fast. It will work, but for the money I prefer the Tapcon bits. They are a little less sturdy but tear through concrete much better. They get dull after 15-20 holes, but cost 1/2 of what this bit costs. I suggest the Tapcon ones and replaced them every 15 holes or so (depending on depth). Bit cost is about $0.25 per hole. Well worth it for a faster bit. May 2, 2016
Rated 1.0 out of 5.0 by Easily worn out. Using a Bosch 1194 VSR hammer drill, I attempted to drill 16, 2 1/4 in holes in my patio concrete One bit lasted for eight (8) holes -- a total of 18 drill inches, and the other bit lasted for six (6) holes -- a total of 13.5 drill inches. Thoroughly disgusted, I went my local ACE and bought a "Tapper" bit, finished out the remaining two holes, and THEN went on to drill an additional 36 drill inches of screw holes into the patio with the Tapper bit.. Clearly the Bosch bits are inferior, as well as being a lot more expensive than my alternative! March 10, 2016
Rated 5.0 out of 5.0 by Amazing This drill bit is amazing I drill 200 holes and the bit still drills amazing!!! April 5, 2016
Rated 1.0 out of 5.0 by 30ish holes and then done? Not sure how long these are supposed to last. I have other Bosch SDS plus bits that I've been using for years now, not constant duty, but still enough that I can expect them to work when I pull them from the case. I'm using these to install some OSB strips onto concrete. I'm getting maybe two dozen holes out of a bit before the tip is just completely melted. I bought another and tried quenching it after each use, they were hot enough after drilling a 2" hole that they got a good sizzle. But the bit still melted after the same amount of usage. I don't know if these are supposed to be considered to be that consumable, but with these costing $2 more than the non hex version, I'm not sure why these even merit the markup. November 4, 2015
Rated 5.0 out of 5.0 by Perfect fit for the project The drill did the job fast, easy to use, durable and lightweig December 8, 2015
Rated 2.0 out of 5.0 by One hole wonder I have purchase over 10 of these in the last month. Great for a couple holes and then quickly dull. Easily bent and worn out. October 14, 2014
Rated 5.0 out of 5.0 by Solid Had to drill into concrete and masonry and this little bit really did the job. September 23, 2014
  • 2016-09-08 T14:54:03.307-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_9, tr_9
  • loc_en_US, sid_100176073, prod, sort_default
2 >>
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 35ms