Model # RA1171

Internet #202716981

Store SO SKU #1000247667

Bosch Benchtop Laminated Router Cabinet-Style Table with 2 Dust Collection Ports (9-Piece)
0000346353549

Bosch

Benchtop Laminated Router Cabinet-Style Table with 2 Dust Collection Ports (9-Piece)

  • Features 2 dust collection ports
  • Includes 3 tabletop inserts
  • Adjustable MDF face plates allow taller pieces to be fed
$15900 /each

Frequently Bought Together

Product Overview

Bosch Hero
Feature 1

Two ports for dust collection

Feature 2

Rigid aluminum router mounting plate is pre-drilled for a variety of routers and stays flat for accuracy

Feature 3

Feed taller pieces with adjustable MDF face plates

Specification Icon


table height

______________________________

14.5 in.

Specification Icon


table length

______________________________

16.0 in.

Specification Icon


table width

______________________________

25.125 in.

Specification Icon


Warranty

______________________________

1 year

Free Shipping to home or store

ON POWER TOOL AND ACCESSORY ORDERS OVER $45

The Bosch Laminated Router Table with Cabinet is compatible with more than just Bosch routers and will immediately expand your woodworking repertoire. Position one of the three included tabletop inserts (1 in., 2 in. or 2-3/4 in. Dia hole) into the router mounting plate to configure the proper setup for your device and intended application. Adjustable MDF face plates on the oversized aluminum fence allow taller pieces to be steadily fed through the cutting platform, while kickback protection and enhanced guidance is afforded via two adjustable feather boards which attach to the fence. 2 integrated dust ports allow you to conveniently hook up 2-1/2 in. vacuum hoses for debris-free operation.

  • Tall aluminum fence (4-7/8 in. x 25-1/8 in.) with adjustable MDF face plates supports taller workpieces; out-feed can be offset for joining
  • Equipped with rigid aluminum router mounting plate pre-drilled for a variety of routers, stays flat and precise for accuracy
  • Includes 2 easy-to-use feather boards which attach to fence and table, supplying extra guidance and kickback protection
  • Accessory slot accepts feather board and 3/4 in. optional accessories such as miter gauge
  • Outfitted with 2 dust collection ports for standard 2-1/2 in. vacuum hoses
  • Includes (3) mounting plate insert rings, (2) out-feed fence shims (1/16 in. thick), (2) adjustable feather boards, (1) starter pin and guard, (1) adjustable clear guard and hardware for mounting most Bosch routers
  • 1-year limited warranty

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

Will the Milwaukee 5616-20 2-1/4 Max-Horsepower EVS BodyGrip Router fit this table?

Asked by: Nedd
The owners manual shows that the 5615 model will work with this table. Milwaukee uses a standard base for their routers.
Answered by: Dusty
Date published: 2015-09-20

does this table come with a router model #ral1171

Asked by: Anonymous
no routers included , but if you need a recommendation go with the bosch router 1617 .It's has a quality hieght lock and top notch height adjustment .Compare them for yourself in store if you can , you will see the difference . Spend the few extra dollars for the bosch
Answered by: ShopDog
Date published: 2015-09-17

does this product cut tiles as well?

Asked by: Anonymous
I would not recommend this table to cut ceramic, stone or porcelain tiles. I use a wet tile saw table for these types of materials.
Answered by: Suinegeht
Date published: 2015-09-17

Bosch RA 1171

what craftsman routers will fit this table
Asked by: Anonymous
The craftsman router that directly fit are listed as Most Craftsman 1/2" collet routers you may also use the adaptor plate RA1186
Answered by: grmpyii
Date published: 2015-09-17
  • y_2017, m_5, d_19, h_12CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_53
  • loc_, sid_202716981, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 121ms
  • QUESTIONS, PRODUCT

Customer Reviews

Benchtop Laminated Router Cabinet-Style Table with 2 Dust Collection Ports (9-Piece) is rated 4.0 out of 5 by 42.
Rated 4 out of 5 by from Additional equipment needed I received this as a gift. The person giving the gift thought it included a built in router. It turns out it doesn't, and it doesn't say this anywhere on the box. I have a bosch palm router and looking through the table router directions the model wasn't listed as one of the compatible models. It did go on to say there are many types of routers you can use, you just need to purchase an adapter plate. So I go to the store to purchase one and think to contact bosch while we're there. They then tell me the palm router isn't compatible at all even with the adapter plate. It won't have enough power. I have used the palm router for a year and never had a problem with it not being strong enough. So this then means I need to purchase myself a gift to the tune of another $200 if I want to use the original gift I was given. Long and short the table works great. It's a lot easier and safer to use than the palm/hand router. I just wish it had said something on the box about not including a router and then about smaller routers not working.
Date published: 2017-01-11
Rated 4 out of 5 by from Went together well and works great! The 'cabinet' door feature is somewhat unnecessary as putting... Went together well and works great! The 'cabinet' door feature is somewhat unnecessary as putting your finger in a hole to pull it open jams your finger in it unless you only use your left index finger exclusively to pull it open. It would be better with a knob or completely off as the door also gets in the way of adjusting the router up and down along with getting it out to change bits. Takes some trial and error to get the aluminum plate flush with the top as there is some play between getting the adjustment screws set slightly high before tightening it down at each corner of the plate. Use a nice, straight edge with a backlight to see where it's high or low and then it should be set. Also did not come with a vacuum adapter from 2.5 to 1.5 as I have a smaller shop-vac. You'll need to get that separately. The little adapters that act as fence guides are somewhat difficult to manage if you take them off an on often as they don't stay with the fence once it's off. You end up putting the fence and the adapters in a zip-lock baggie when not in use, or you can try to tighten the screws against them to keep them together.
Date published: 2017-01-10
Rated 4 out of 5 by from Bosch router Table Great pice of equipment and easy to use. Assembly is here I had issues. The directions call for numerous different types of bolts and they are not clearly marked. After jumping that hurdle I completed assembly and use it daily now!
Date published: 2017-03-07
Rated 5 out of 5 by from Nice I recently purchased one of these through Home Depot. Although the box was damaged the router table was not. It was fairly easy to assemble with good directions. It was easy to get the insert plate level with a bit of patience.
Date published: 2017-01-14
Rated 5 out of 5 by from I needed a quality table, and I got what I needed Needed a table to fit my DeWalt router without any drilling. This table was pre drilled for various router bases including mine The table was solid construction, and easy to assemble. The switch took some patience to assemble, but if I weren't patient, I wouldn't be much of a woodworker. Everything was nicely machined, and came with multiple inserts. The switch accommodates both the router and the shop vac. Very handy to start both with one motion on the front of the table.
Date published: 2017-02-05
Rated 4 out of 5 by from Works mostly well I purchase this table several months ago. I am experienced amateur. This was my first time owning and using a router table. Set up was relatively easy and though I have not used all of the features, the one I have used have been pretty good. My biggest complaint is this: shortly after I began using it, I noticed my cuts would have inconsistencies towards the middle of the board caused by the mounting plate sitting below the tabletop level. I added some thin washers and thought I had the problem fixed but yesterday while routing almost an entire project I noticed the problem again. I need to add some of those very thin plastic washers. In the meantime, it just takes a bit of extra and annoying sanding. I have not noticed some of the problems with the fence others have but it can be sticky and takes a delicate touch at times.
Date published: 2017-04-26
Rated 4 out of 5 by from I do LIKE this table I am a moderately decent woodworker and this table fits my needs. My MAJOR complaint is the router lift. It doesn't lift the router. I need to use one hand under the table to lift or lower the router because the "through the table handle" just spins. I would actually like to purchase a much more accurate lift but I cannot find any products that are compatible with the table.
Date published: 2017-02-19
Rated 1 out of 5 by from disappointment bought router table and a bosch router as they are advertised to go together such as one can adjust router depth with use of allen wrench thru to metal insert in table top. using directions (not provided in router table package, had to call and have them sent), could not make them come in aligment so that router depth can be adjusted, will have to redrill your hole to match router. also had water damaged door in router table, had not opened as soon as purchased, waited several months for time to put table together, had to pay for damaged part, also had multiple missing pasts, screws, nuts, used for the various things such as the fence and fingerboards, which also entailed multiple calls to order, again had to pay for parts. only plus noted is the persons answering phone were patient and pleasant. at this time router table with router attached setting in back of shop, not have been used yet. robert hood.
Date published: 2016-12-17
  • y_2017, m_5, d_19, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_42
  • loc_, sid_202716981, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 43ms
  • REVIEWS, PRODUCT