Free Shipping and BOPIS


Model # KTR14X C1

Internet # 202047070

Store SKU # 393150

1/2 in. Nominal Sweat Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Straight Valve

This item has been discontinued.
The Home Depot no longer carries this specific product.

$8.67 /each




Model # KTR14X C1

Internet # 202047070

Store SKU # 393150

BrassCraft 1/2 in. Nominal Sweat Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures - faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a 90° turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without turning off water to the entire home.

  • Compatible with copper
  • Smooth, quarter-turn operation, on/off flow control with a 90° turn of the loose key handle
  • Brass ball ensures smooth operation without freeze-ups even after long periods without use
  • Machined body provides strength, durability and long-lasting performance
  • Chrome-plated brass
  • Temperature rating: 40° to 180°F
  • Pressure rating: 125 psi maximum
  • No-lead certified
  • IAPMO and CSA listed to ASME A112.18.1/CSA B125.1

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.


Product Height (in.) 
Product Length (in.) 
2.75 in 
Product Width (in.) 
Valve Inlet Diameter (in.) 
Valve Outlet Diameter (in.) 
Compatible Pipe Material 
Sweat x Comp 
Maximum Pressure (psi) 
Maximum Working Temperature (F) 
Product Weight (lb.) 
.21822 lb 
125 psi 
Warranty / Certifications
Manufacturer Warranty 
Limited Manufacturer Warranty 


Rated 3.0 out of 5 by 2 reviewers.
Rated 5.0 out of 5.0 by Never had an issue I use brasscraft quarter turn sweat on valves almost exclusively during bathroom and kitchen remodels. Despite the previous reviewer having issues with melting the valve handle, I have never had this problem. The valve is to be open during sweating so that the nylon ball stop on the inside does not melt. If you are working on clean and dry copper pipe you should be able to sweat this on with less than 30sec of heat without any issues. The multiturn valves must also be open during sweating so that the rubber stopper in there doesn't burn up (which is more likely because the rubber melts at a much lower temp than does the nylon). Also, multiturn valves fail more quickly because the rubber stopper deteriorates and can build up lime/calcium that prevents it from shutting fully. The quarter turn valves do not have this issue. Multiturn valves can also become stuck in the open position and be very difficult to close. There are occasions when a faucet springs a leak or a toilet becomes clogged and you want to be able to shut the water off at that fixture ASAP....1/4 turns are the way to go. I give 4 stars for ease of installation because the shark bite valves are much easier to install. However, I would not recommend the shark bite fittings for permanent use because I have seen them develop a drip over time and would not trust them in my brand new kitchen or bathroom. January 5, 2015
Rated 1.0 out of 5.0 by Poor quality for price Directions for copper soldering advise to open valve. Despite my long professional experience, cheap "pot metal" handle MELTED with minimum heat for sweating. Also, another previously installed by me slowly leaked when fully shut off. Now hate it... Going back to non-quarter turn regular shutoffs. August 16, 2014
  • 2015-10-03T11:59:35.916-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_2, tr_2
  • loc_en_US, sid_202047070, prod, sort_default
1-2 of 2