Model # PSC1081 K5

Internet #100112627

Store SKU #345781

BrassCraft Safety+PLUS Gas Installation Kit for Dryer and Range (60,500 BTU)
0039166091645

BrassCraft

Safety+PLUS Gas Installation Kit for Dryer and Range (60,500 BTU)

  • Approved for indoor and outdoor use
  • Fits all current and most older dryers and ranges
  • Leak detection solution and pipe thread sealant included
$2997 /each
store icon Loading Buying Options...
package icon Loading Buying Options...
Sorry, but we ran into issues loading these options. Please try refreshing.

Frequently Bought Together

Product Overview

  • Approved for indoor and outdoor use
  • Fits all current and most older dryers and ranges
  • Leak detection solution and pipe thread sealant included
BrassCraft's Dryer & Gas Range Gas Installation Kit contains everything you need to connect most gas dryers and ranges to your gas supply. BrassCraft's Safety+PLUS gas connector combines excess flow technology with the advanced corrosion resistance of ProCoat, to provide a safer gas connector for home and family. In the event of a gas line rupture or disconnect, the Safety+PLUS valve restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Our stainless steel gas connector is protected with a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available. The kit includes easy-to-read installation instructions.
  • 1/2 in. O.D. x 48 in. length corrugated stainless steel gas connector with ProCoat coating to withstand prolonged exposure to harsh household chemicals
  • Safety+PLUS Excess Flow Valve protects against gas fires and explosions - 1/2 in. MIP (with 3/8 in. FIP Tap) connection to gas supply or gas ball valve
  • Steel fittings included: (1) 1/2 in. MIP (with 3/8 in. FIP Tap) fitting, (1) 1/2 in. FIP fitting, and (1) 3/8 in. MIP fitting
  • Fits all current and most older dryers and ranges
  • Leak detection solution and pipe thread sealant included
  • Use with natural and LP (propane) gases
  • Gas Connector is 100% leak tested. Safety+PLUS excess flow valve is 100% performance tested
  • Approved for indoor and outdoor use
  • Temperature rating: 32 Degree to 150 Degree F
  • Pressure rating: 1/2 psi maximum
  • Designed, machined and assembled in the USA
  • CSA certified

Product Overview

  • Approved for indoor and outdoor use
  • Fits all current and most older dryers and ranges
  • Leak detection solution and pipe thread sealant included
Model #: PSC1081 K5
Sku #: 345781
Internet #: 100112627

BrassCraft's Dryer & Gas Range Gas Installation Kit contains everything you need to connect most gas dryers and ranges to your gas supply. BrassCraft's Safety+PLUS gas connector combines excess flow technology with the advanced corrosion resistance of ProCoat, to provide a safer gas connector for home and family. In the event of a gas line rupture or disconnect, the Safety+PLUS valve restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Our stainless steel gas connector is protected with a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available. The kit includes easy-to-read installation instructions.

California residents: see   Proposition 65 information

  • 1/2 in. O.D. x 48 in. length corrugated stainless steel gas connector with ProCoat coating to withstand prolonged exposure to harsh household chemicals
  • Safety+PLUS Excess Flow Valve protects against gas fires and explosions - 1/2 in. MIP (with 3/8 in. FIP Tap) connection to gas supply or gas ball valve
  • Steel fittings included: (1) 1/2 in. MIP (with 3/8 in. FIP Tap) fitting, (1) 1/2 in. FIP fitting, and (1) 3/8 in. MIP fitting
  • Fits all current and most older dryers and ranges
  • Leak detection solution and pipe thread sealant included
  • Use with natural and LP (propane) gases
  • Gas Connector is 100% leak tested. Safety+PLUS excess flow valve is 100% performance tested
  • Approved for indoor and outdoor use
  • Temperature rating: 32 Degree to 150 Degree F
  • Pressure rating: 1/2 psi maximum
  • Designed, machined and assembled in the USA
  • CSA certified

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.

Specifications

Dimensions

Inner diameter (in.)
0.375
Outer diameter (in.)
0.5
Product Depth (in.)
2.13
Product Height (in.)
9.13
Product Length (in.)
48
Product Width (in.)
8.69

Details

Connection type
MIP x MIP
Gas Vent Pipe and Fittings Accessory Type
Gas Appliance Connector
Inner material
Stainless steel
Maximum Pressure (psi)
0.5
Maximum Working Temperature (F)
150
Minimum working temperature (F)
32
Outer Material
Stainless steel
Product Weight (lb.)
1.14074lb
Returnable
90-Day

Warranty / Certifications

Certifications and Listings
CSA Listed,IAPMO Certified
Manufacturer Warranty
Limited Manufacturer Warranty

Specifications

Dimensions

Inner diameter (in.)
0.375
Outer diameter (in.)
0.5
Product Depth (in.)
2.13
Product Height (in.)
9.13
Product Length (in.)
48
Product Width (in.)
8.69

Details

Connection type
MIP x MIP
Gas Vent Pipe and Fittings Accessory Type
Gas Appliance Connector
Inner material
Stainless steel
Maximum Pressure (psi)
0.5
Maximum Working Temperature (F)
150
Minimum working temperature (F)
32
Outer Material
Stainless steel
Product Weight (lb.)
1.14074lb
Returnable
90-Day

Warranty / Certifications

Certifications and Listings
CSA Listed,IAPMO Certified
Manufacturer Warranty
Limited Manufacturer Warranty

Questions & Answers

can you put two or three together? or do they make them longer, special

can you put two or three together? or do they make them longer, special
Asked by: harley
Harley – The gas connectors are not designed to connect to each other. There should be a single connector from the gas shut off valve to the appliance. We do make gas connectors in lengths up to 72 inches that may work for your application. Please contact our Customer Support Team at 877-272-7755 for assistance.
Answered by: BrassCraft Mfg
Date published: 2017-06-06

Can this product be used to connect an outdoor gas grill to a new 500 lb LP tank that I had buried in my backyard?

Asked by: Gasgrill1
Thank you gasgrill1 for asking the question. BrassCraft gas connectors are certified to ANSI Z21.75 / CSA 6.27 standard for “Connectors for Outdoor Gas Appliances & Manufactured Homes”. This standard specifically requires that the connector be used above ground and that the gas pressure within the system be no greater than 1/2 psi. That means that the connector must be installed downstream from the pressure regulator. This standard also requires that the appliance be stationary - meaning you cannot install this product on appliances with wheels or casters. For complete selection and installation instructions, please refer to our guide included on the product page at http://www.homedepot.com/p/BrassCraft-Safety-PLUS-Gas-Installation-Kit-for-Dryer-and-Range-60-500-BTU-PSC1081-K5/100112627. Any additional questions please do not hesitate to contact our customer support team toll-free at 877-272-7755
Answered by: BrassCraft Mfg
Date published: 2016-10-07

my gas range's inlet says 1\2 inch but i buy 1\2 inch adapter and does not fit tight, is that correct?

i install the 1\2 inch adapter fitting into my range and it fits loose untill i tighten all the way, is this correct? (it wiggles as i tighten it, until tighten completely
Asked by: joekc
Dear Joekc - The adapters that you refer to have “tapered” threads so the first couple turns by hand may feel a little loose. Make sure you use a pipe thread sealant or pipe dope to seal the connection. Once hand-tight, use an open-end or adjustable wrench to complete the installation. Make sure to leak test the connection with soapy water or leak detection solution; bubbles will indicate a leak. Be sure to read the complete installation instructions at (http://www.homedepot.com/catalog/pdfImages/ea/ea7dc718-95fd-4033-b680-3a9d0c17db69.pdf) Should you have any questions please feel free to contact one of our Product Experts toll-free at 877-272-7755.
Answered by: BrassCraft Mfg
Date published: 2017-06-06

on the gas flex lines do they need teflon tape or compound?

Asked by: chuck
Thank you Chuck for your question. It depends on which connection you are making. The steel or brass fittings included with this connector are flare by pipe thread. On the pipe thread connections between the fittings and the appliance inlet or gas supply please use a gas-rated thread tape or compound on the male threads only. As for the flare connection between the fitting and the gas connector itself - please DO NOT use thread tape or compound. This connection type seals on the 45 deg. flare surface. Compounds and tapes may interfere with that seal, creating a potential leak and making the connector unsafe for use. Each connector has step-by-step installation instructions included. Please read those thoroughly before installing the connector. If you have any additional questions please do not hesitate to contact us toll-free at 877-272-7755. Have a great day!
Answered by: BrassCraft Mfg
Date published: 2017-07-10
  • y_2017, m_10, d_15, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_22
  • loc_, sid_100112627, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 106ms
  • QUESTIONS, PRODUCT

Customer Reviews

Safety+PLUS Gas Installation Kit for Dryer and Range (60,500 BTU) is rated 4.9 out of 5 by 8.
Rated 5 out of 5 by from Well built with accessories, thread sealer and leak detector. I... Well built with accessories, thread sealer and leak detector. I did not end up using all the connectors but everything seemed to be well made.
Date published: 2017-07-18
Rated 5 out of 5 by from easy. complete fittings easy. complete fittings
Date published: 2017-09-05
Rated 5 out of 5 by from Complete kit This kit had everything I needed to connect our new stove. Nice all-in-one kit, although it is a bit pricey.
Date published: 2012-07-04
Rated 5 out of 5 by from Just what I needed This is a very good product, easy to install. Had a professional install it and they found it to be a very good item.
Date published: 2013-12-10
Rated 5 out of 5 by from Worked perfect Get connected my dryer with no problem. The gas is not leaking anymore. Perfect!
Date published: 2016-02-10
Rated 5 out of 5 by from GAS INSTALLATION KIT THIS IS A GREAT PRODUCT,WAS EASY TO INSTALL,WORKS GREAT
Date published: 2015-05-21
Rated 4 out of 5 by from nice kit Kit worked ok for what I needed. Inastall can be limited and more fittings might be needed in certain conditions. A bit pricey but works.
Date published: 2015-02-10
Rated 5 out of 5 by from BrassCraft 48 In. Gas Dryer Installation Kit The BrassCraft 48 In. Gas Dryer Installation Kit was easy to install.
Date published: 2010-06-01
  • y_2017, m_10, d_15, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_8
  • loc_, sid_100112627, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 104ms
  • REVIEWS, PRODUCT