Rated 4.4 out of 5Â by 34
Rated 5 out of 5Â by Larry This product has great features.
I needed a quieter compressor and this fits the bill. It is quiet enough that you can have a conversation right next to it while it is charging. It's great for blowing dust out of the garage and filling bicycle and other tires. Haven't tried it with a nail gun yet, but recharges in less than a minute. The aluminum tanks make me less worried about corrosion due to there always being water in the tank when I release the pressure at the end of the day. It have a very handy finger-switch for releasing the pressure. Much easier than the knurled fittings on most generators. I have it connected to a 50 retractable hose mounted to the ceiling. The compressor is small enough to fit under my workbench (picture). I couldn't be happier with this compressor.
April 16, 2014
Rated 3 out of 5Â by recon this brand sells quietness , not thoughness
First day of use I put my air hose in the coupler and it leaked, so I removed my air hose and noticed there were no rubber seals in that one coupler. I put my air hose in the second coupler and went to work. The compressor worked great it seem to do well with my 3m pistol 3" sander. Second day of use I put my air hose in that #2 coupler and its leaking now .I guess when I removed my air hose from the day before it blew the seal out .I go to my local auto paint supply store and buy two new 1/4" male couplers for it. I wrap the treads with teflon tape and install my first one. I put the coupler on hand tighten it about three turns. I get about three or four turns with a wrench and snap! the stem that held the coupler broke. cheap pot metal , cheap couplers . the compressor may be good ,but the attachments need improvement
October 2, 2014
Rated 5 out of 5Â by Ciengarde Second Times the charm
The first one I got was defective inside the box but no outside damage to suggest how it got that way.
California Air was most helpful and I had no problems returning to HD. Because its a online only Item I had to make a new order to get a replacement. So had to wait another 5 to 7 days to get a replacement.
The Replacement unit works Great. Just like other reviewers said it would it charges up fast and is not very loud when it is charging up.
The Tank is small so the supply does not last long but the compressor seem to be able to compensate for that to a certain degree. You can use a extension cord with it according to the written instruction so long as its at least 12 gauge and not more than 25ft long. I needed to get special extension cord for it as all mine where not heavy enough. Also you need to make sure where ever you plug it in at can really handle 15 amps or more.
Oh and it is heavy and a bit awkward to carry by the handle.
September 30, 2014
Rated 5 out of 5Â by AAAtool Works as stated in the ad
Had mine shipped to Home Depot to avoid a possibility of poor shipping.
Came to me in perfect shape. No damage, but there was a loose pressure switch (sits behind the ON/OFF switch box).
Using a dB (A and C) meter, sound was measured at 68dBC (dBC includes freq below 500Hz dBA is greater than 500Hz). Note: Every 10 dB is considered a perceived human hearing of doubling of loudness so the Husky 4 gal equiv. (1.5HP, 3.8 @40 2.8 @90) is more than twice as loud as this, for example.
I have a 4CFM sander from Harbor freight (25% duty cycle so really it requires 12 to 16 CFM for on all the time performance). I charged the tanks and ran the sander without stopping and it seemed to maintain a good grinding ability at 45 psi without stopping. On the Husky 4gal the same stopped after 10 seconds, meaning I could stop the rotation of the sander with my hand.
I have a blower. I can hold it ON and the air blew constant at 45 psi, down from 123 psi. The outlet diameter of the blower is about 3/32" so it is pretty wide open. The air use at 45 psi was very good and very usable so I didn't care.
The tank filled from 45 to 123 psi in less than 30 seconds, I would say. It is astonishingly quick to charge. From 0 to 123 it is amazing how quick it is compared to all the other compressors I have used.
It is heavy so I would not want steel tanks. It lifts with balance, however. Picking it up when it is hot could be an issue.
The motor looks to be of great quality. Overall, I think the build is equal to any I have seen at Home Depot so I have no complaints. From the front it is aesthetically nice as well, better than the pictures on the websites. Dials and so on are equivalent in quality to others. I have no concern because this stuff is easy to replace with better if that is what I wish to do in the future. The parts are not expensive to upgrade, that is.
Mine came with the new air release valve design California Air Tools just came out with. It was much better than that found on the Porter-Cable pan compressor which, btw, is about three times as loud as this compressor. That compressor you cannot have in the same room without having your ears ring. Anyway, it is easy to drain. I wanted Alum tanks because I plan to leave it charged so I don't want rust in the tanks. I left it charged and their was no drop in pressure at all so I was lucky with seals, I guess.
The motor gets very hot. You will not be able to touch it after about 15 min of 100% on time. They say in the manual that you can have it on 100% for one hour.
The filters are made of metal, not plastic. If you twist them, you will see what looks to be a mini paper -- car like-- air filter. I guess this can be replaced as the filters are made to twist in half and the paper filters, serviceable. I guess you could blow the filters out? In any case, these are not like the red filters you can get at Harbor Freight which are used for Powder Coating.
I want to try Soda Blasting. I think it would work as the volume of air at 40 psi is 7CFM. I use a 12CFM air compressor to do this in a high dollar blasting cabinet and I have to dial that down to 40PSI for a better finish so I know I can be happy at 40 psi, and because the Harbor Freight 15 gal soda blaster is rated at 7 CFM at 40, I should be OK with this compressor. As my sanding tool eats air like crazy and since it seemed to be working -- good enough to sand anything I need -- at 40 psi, I believe the air is 7 cfm and believe, therefore, that the soda blasting tank should work.
Overall, this is the best compressor I have used and I have used many. I don't know how long this will last. I say I'm concerned because of the temp of the motor when used heavily. However, because all other compressors I have used have plastic over the motor, I would guess that they also got very hot so I do not have a comparison for this concern. The sound is no louder than an 10" house fan set on High. I would say it is quieter, in fact. I chose this over the 10 gal 2HP California Air Tools compressor equiv. as the 10 gal does not give you any more than about 20 seconds more of time before the motor runs again. That is not worth the weight of a ten gallon steel tank. My air tools are likely going to make the compressor run all the time anyway, but it is rated for 1 hour so I should be fine and because it is so darn quiet, why should I care that the motor is on? The use of the tool is 3 time louder so why care that the motor is on as I can't even hear it over the tool? They say the motor lasts longer than the traditional, as it is electric, so if this becomes so, I will never own another type again as the sound and high CFM of this compressor is hard to beat...in fact, I don't think it has been, yet.
October 20, 2013
Rated 3 out of 5Â by PCfromKY This is quiet but may have problems at the onset.
Purchased in Nov. 2013, I looked at numerous products and read many reviews before purchasing this compressor. What other reviewers said about shipping was true. This came in a single box with no styrofoam protection on the sides. The brass pressure switch adjustment valve wore a hole the size of my thumb through the box but luckily it wasn't damaged.
The set-up instructions are very poor and the assembly view drawings very small to determine the parts and their number. After running the compressor for one hour, a pressure hose from the pressure switch to the air manifold developed a leek. Upon inspection, the line was resting against the heat fins located on top of the pump motor and the slight vibration and heat caused the leek to develop. In addition, the air fitting was turned toward the pump and the line was just long enough to reach. Very poor planning and engineering with a disregard to improving quality and inspection.
I did get an immediate service tech without waiting and told him of the situations. He was polite and said there would be improvements in their shipping boxes this Jan. 2014. He sent me the parts I needed in two days.This is made in China for this USA company and the lack to basic quality control and improvement hasn't seemed too concerning since these comments are similar to many others in the past. I thought they would have corrected many issues and improved their product ... but it is Chinese!!
I rate this as three stars since it is very quiet ( one reason for purchase) but priced high for the lack of quality control and shipping.
January 8, 2014