Campbell Hausfeld 115 Volt 100-Amp MIG/Flux-WG216001AV - The Home Depot

Campbell Hausfeld

Model # WG216001AV

Internet # 202754695

115 Volt 100-Amp MIG/Flux

Campbell Hausfeld 115 Volt 100-Amp MIG/Flux

This item has been discontinued.
The Home Depot no longer carries this specific product.

$236.90 / each


Model # WG216001AV

Internet # 202754695

The WG2160 is an ideal MIG/Flux-core wire feed welder to have around the house. It has the ability to weld in the Flux-core or MIG setting. Four different heat settings allows the user to zero-in to the correct heat setting depending on the application The convenient power and versatile design make this MIG welder a must in anyone's garage

California residents: seeProposition 65 information

  • Easy to change polarity, mig ready, built-in gas liner and valve, quickly change from flux to mig
  • Independent drive deck transformer provides consistent wire speed for smoother welds
  • Perfect for projects and repairs, weld with flux-core wire (no gas required) or Mig wire (MIG wire and shielding gas required)
  • Thermal overload protection automatically shuts off to avoid overheating
  • infinite wire feed allows adjustment for smooth even weld bead
  • 4 heat settings adjusts output power to match metal thickness
  • Home Depot Protection Plan:

    Home Depot Protection Plan


Assembled Depth (in.)  175 in  Assembled Height (in.)  11.5 in 
Assembled Width (in.)  10 in  Product Width (in.)  11 
Engine Power  Electric (AC)  Maximum amperage output (amps)  100 
Minimum amperage output (amps)  30  Power Tool Product Type  Welding Supplies 
Returnable  90-Day  Tools Product Type  Power Tool 
Torch included  Yes  Voltage (volts)  115 
Welder Type  MIG  Welding Supplies Product Type  Arc/Stick Welder 
Warranty / Certifications
Manufacturer Warranty  5 Year Limited Warranty 


Rated 3.8 out of 5 by 8 reviewers.
Rated 4 out of 5 by So far So Good I have used the welder to build a Wood Burning Stove out of a sheet of 14 Gauge Steel. The welder worked good for this thinner steel and was able to make really nice welds. It worked just as good as the more expensive Lincoln welders I've used. I've used this on thicker angle iron to make a welding table and I had no problem making nice strong welds. February 14, 2014
Rated 5 out of 5 by good welder I am a professional welder and this little cracker Jack welder is perfect for the home welder I highly recommend it November 6, 2012
Rated 2 out of 5 by Has potential, but... I'm a beginner welder. Before buying this welder I got a Harbor Freight 90 amp flux core welder to test out the waters. After using that welder I wanted to upgrade so I got this welder. It appears to be a sturdy machine, but when I tried it out there were two main things that bugged me about it. 1) when feeding the wire through, the wire got stuck at the tip and wouldn't go through the contact tip. I guess I could have taken the contact tip out and then screwed it back on, but I would figure that it should go through without getting caught there. The wire ended up coiling up just past the wire feeder and was wasted. This isn't such a big problem since it's easily remedied by taking off the contact tip. 2) When welding even if the voltage at the max, it would not do a smooth weld unless the wire feed was set at 1. Above that it felt like the gun was jumping at me and the sizzling (wire welding sound) was sporadic. Even when clamping the ground to the actual work piece. The HB welder was smoother than this one and I used both on the same work piece (i.e. practice piece). Only being able to weld with a wire feed speed of 1 is not acceptable and I also had a hard time getting penetration even with voltage at max. Pro: - can use 15 or 20 amp circuit. It says on the voltage dial how far you can go with using a 15 amp circuit. You don't need a 20 amp circuit unless you need to go to the max setting on the voltage (the voltage has four settings, 1 to 4), though I did use it on max voltage on a 15 amp circuit and it didn't trigger the breaker. - can use mig or flux core Con: - not being able to use wire speeds above 1. - wire getting caught when feeding the wire through, but only happens when first first getting the tip of the wire past the contact tip. After that it was fine. - the regulator is junk. No gauges to tell you how much pressure is in the tank. - no attachment for the spool so you can use a 10 lb. spool. Not sure if it can handle that big of a spool. It doesn't say in the instructions. November 16, 2014
Rated 5 out of 5 by This product great for the money I'm very happy with my welder. It's great for auto body repair repair and a good start for a beginner like myself. Can't ask for more. December 27, 2012
Rated 5 out of 5 by Easy to set up and use The set-up instructions were a little incomplete. There was a part left over after following the instructions. Not too difficult figuring out where it went. Once set up, it works well so far. A few youtube videos and I am learning. My first few welds failed, but it was because I was tenuous, using it more like a glue gun than a welder. Now that I've cranked the heat setting up to penetrate the thickness of the metal I'm working with the welds are much better October 8, 2013
2 >>


Standard Shipping includes delivery by small parcel service. Processing time varies by product.

Orders for this item may be expedited for an additional fee.

Other Delivery Options:

Express and Expedited shipping options are also available. Estimated arrival times are available in checkout.

If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.