Rated 3.2 out of 5 by 30
Rated 5.0 out of 5.0 by Kanzan Great Stuff
The 3/4 in Birch Plywood is perfect for making storage item, cabinets, etc. Easy to cut using my saw with the Rockwell cutting attachment to cut pieces to size. The plywood needs just a light sanding to provide a smooth surface (Except for the foot prints delivery company walked on top of the first piece. Easy to glue/nail finish strips to raw edges to give a more finish look to completed project.
October 2, 2016
Rated 5.0 out of 5.0 by daninkaty Nice grain look
This sheet of birch has a nice grain finish to it that goes the 8 ft. length. It is made of 5 layers. Some of the 4 ft. end layers have about a 1/2" space in them. With a good sharp blade this cuts very nice and smooth. When staining it takes the stain very well and evenly. This is a nice piece of plywood to work with and makes a quality looking project in the end.
September 28, 2016
Rated 5.0 out of 5.0 by deweys1427 Perfect Plywood
This is some quality plywood, especially in todays world of corner cutting etc. Very few voids and repair spots. I used this sheet to make some boards, 2' x 4' for corn hole games and they came out great. I was going to snap a couple of pics before I sent them to the painters but forgot. I used some Kreg Joints on the frame so the top had no screw holes in it. Made for a great finished product, that I expect to last for years. Sanding was minimal because these will be painted, but I have stained this plywood as well and it comes out beautiful. I will snap pics, and edit post when they come back from the painters. They will be KC Chiefs colors for those interested.
October 26, 2016
Rated 5.0 out of 5.0 by TomO It's C3 plywood
This is C3 plywood folks. That means you'll see more repaired knots and voids on a sheet, and some defects will be left as is. This type of plywood grade is a good choice for projects where you won't necessarily need a 'show' finish. I used this plywood for approx 100lf of garage cabinets. I did not experience any delamination, excessive voids nor sand through. Anyone looking at this plywood for fine furniture should be looking for A1 grade plywood
September 12, 2016
Rated 5.0 out of 5.0 by Nonsheep Absolutely Beautiful! TOP QUALITY - Great For Making Laundry Room Cabinets
I ordered this plywood to custom build my own cabinets due to the miss shaped kitchen walls. I was worried about ordering online, however they were shipped directly to my home without any issues! Communication was quick & friendly & helpful too. This Plywood is Absolute Top Quality! Smooth to the touch without any mars on the face at all. Very Hefty feel also and they weigh in at approximately 72-75 lbs each! Upon working with the sheet it cut well & held the fasteners quite well. Some Natural Timber Oil to bring out the grain & Voila - Awesome Laundry Room Storage!
July 28, 2016
Rated 5.0 out of 5.0 by carnini Great Plywood without any off gassing
First off I received two sheets of this plywood in addition to another order that was the thinner version. It was helpful that I was able to compare the product in general. It was shipped form a distance so I was not surprised that 1 of the boards on the outside was really banged up. I figure I can use this piece for a bottom or an unseen support etc.
When looking at the better quality face, it was great looking and I would have no problem using it and having it being seen. This went for both boards even though one was banged up. The back varied a lot in the two boards. One back looked much lower grade while another back was almost face quality which was unexpected. My advice would be to look carefully, since its a natural product, choose the boards that fit your project.
The plys on the boards I had where really good. The top plys where really thick and I had no problem sanding it down, etc. I found the plys when I cut where even and they all looked thicker than I tought.
For the price, I think this is a good alternative to plywood if your looking for a greener plywood. For the quality make sure to look over the boards.
August 19, 2016
Rated 1.0 out of 5.0 by ToddNY Very poor and unusable
Not good. Got two loads of it in. Liked the first load until I started using it and the voids inside made it unusable for a finished product. Whole sections without anything under the laminate just made it like a bubble. As soon as it's cut, it deflates and gets ripples in it. Second shipment in just looked like bad period. Had to use it for paint only and even then, in areas that don't show.
December 27, 2015
Rated 3.0 out of 5.0 by Blackbeered Good for Carcasses
Don't expect cabinet-grade plywood here. It's a 5-ply with thin veneers.
Being someone who pockets these materials in dadoes, what I found most interesting was the high variation in thickness throughout the board. The nominal thickness measured in at 0.718" but varied from 0.702 to 0.731" ... and that leaves a lot of "grinning" when the dado set is dialed in for the minimum value. So materials like this are best-suited for pocket hole joinery to a face frame.
Also, neither side was 'clear' and to my standards, not stain-grade.
July 4, 2016