Free Shipping and BOPIS


Model # 09330B

Internet # 202251655

Store SKU # 918214

3H-10H/C Stem for Price Pfister Faucets

This item has been discontinued.
The Home Depot no longer carries this specific product.

$13.97 /each




Model # 09330B

Internet # 202251655

Store SKU # 918214

Get the DANCO 3H-10H/C Stem for Price Pfister Faucets to finish the installation of your faucet (not included). This stem is constructed from durable metal.

  • Metal construction provides durability
  • Chrome finish
  • Seat-type stem
  • For use with a Price Pfister faucet (not included)
  • Suitable for hot- and cold-water applications


Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
Color Family 
Cut for Custom Fit 
Fits Faucet Brand 
Price Pfister 
Plumbing Part Type 
Stem Type 
Water Type 
Hot & Cold 
Warranty / Certifications
Manufacturer Warranty 
Limited Lifetime 


Rated 3.4 out of 5 by 25 reviewers.
Rated 4.0 out of 5.0 by Hot water was easy, cold gave me trouble The hot water cartridge was a breeze. Everything went as expected. I ran into trouble when I tried to install the cold water side. I was finally successful when I went on this site and read the other reviews. To make the cold water handle work, you need to remove the c-clamp at the top of the cartridge (I used a dull letter opener for this). Then you need to flip over the little ring that pops off. Don't force it. If it's in the right position, it'll slide right on. Then replace the c-clamp and you're good to go. This product really should have come with instructions. I was going out of my mind until I stumbled across these instructions on this site. December 26, 2013
Rated 2.0 out of 5.0 by good for Hot water only I'm replacing the Cold 910-900 cartridge on my 87180SS Savannah faucet. This cartridge works when setup for Hot, but when I flip the ring over to use it for Cold, it lets the lever go beyond the Stop point and the water starts dripping out. I have to back it off about 1/3 of the way to stop the drips. Looking at the bottom of the cartridge you can see that it turns beyond the point where the valve is closed, and when the lever is fully open, the valve is not. Everything lines up OK when used for Hot water, but it's misaligned by 1 tooth for Cold. Also, I haven't tried hammering it, but my lever handle doesn't seem to fit over these shaft splines. June 11, 2013
Rated 4.0 out of 5.0 by Stopped the leak The questions answered by Danco to David was extremely helpful. I had went to the Danco's website and it was down for maintenance. Thanks for the Q&A here on the Home Depot site. It got me back on track with my project. August 29, 2015
Rated 4.0 out of 5.0 by Easy repair The Danco 3H-10H/C was a easy repair but came with no directions. After installing the hot and cold side they both turned in the same direction. After doing some research I found out to make the cold side turn in the opposite directions you need to take the C clamp off at the top of the stem and pull off a slotted ring (under the C clamp). Turn the slotted ring over and put it back on . This allows the handle to be turned in the opposite direction. Fix my problem and no more water leak. June 17, 2012
Rated 1.0 out of 5.0 by I got a $14 washer... I bought these and like another reviewer when installed it would not shut the hot water off completely. So I removed the black o-ring from the bottom and installed it on the original P-F valve, and that fixed the drip. So I paid 14 bucks for a washer. The overall poor rating is for the lack of instructions on how to switch the operation from hot to cold. June 21, 2015
Rated 5.0 out of 5.0 by Perfect Fit For Pfister This unit fits perfectly in my Pfister bathroom sink....installation takes about 30 seconds....if you're having difficulty installing this item then you probably have the wrong unit.....this is an exact fit replacement and there should be no trouble installing the pdf by Googling the part number (09330B) if you need to reverse the direction for the cold's straight forward. March 20, 2015
Rated 2.0 out of 5.0 by reuse old stop ring to fix As others have said, flipping the stop ring to use for a cold stem makes the stem unusable: not fully open when on, leaky when off. The new stem's stop ring bosses are too big (the stop bosses are too wide, in an angular sense). I was able to use the stop ring from the old stem to make the stem work much better in this application. A little work with a file may help further, but...sheesh! Maybe a bad batch of stems out there? August 25, 2013
Rated 5.0 out of 5.0 by Replaces Price Pfister 910-900 This is a direct replament for OEM part 910-900. Easy to install, bought two replaced both hot and cold. Out of the box mine was ready to go for the hot water, removed the retaking ring and flipped for the cold water. March 22, 2015
  • 2015-10-02T14:02:11.297-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_25, tr_25
  • loc_en_US, sid_202251655, prod, sort_default
2 >>