Rated 2.5 out of 5 by 11
Rated 1.0 out of 5.0 by PaulG MOST USELESS thing I ever bought at Home Depot
This is an adapter kit that does not adapt. It is sold to fit four different type Delta shower valves and did not fit mine AT ALL.
The outer cover is cheap, thin plastic and molded to require me to try and cutout MORE of the tile around the valve opening due to a raised center piece. The wall gasket does not fit tightly into its groove and is not compressed uniformly against the wall, which would lead to leaks and mold.
It is cheaply made. It is extremely overpriced. It is poorly designed (maybe trying to fit too many valve types?)
October 15, 2016
Rated 1.0 out of 5.0 by TBone Poor Design
I concur with all the other reviews concerning the handle. Terrible, terrible design. I can't believe Danco hasn't come up with a better design for this model. The way the inside mating part of the handle is formed creates too much play when mounted to the adapter. Also, the small 6-32 set screw will not tighten securely enough to make it practical. After a few uses the handle starts to wobble and the screw backs out. I contacted Danco and the rep recommended applying Loctite blue thread loc on the screw. I don't think this would remedy the entire problem. I am going to spend the extra bucks and buy the OEM replacement.
October 23, 2015
Rated 4.0 out of 5.0 by Schweinehunde Perfect way to upgrade your old Delta shower
First off, I purchased this kit despite all the negative reviews I read here. I am in the process of remodeling our vintage 1980's guest bathroom and since Delta does not make a trim kit upgrade for their antique models, this Danco kit is literally the only option out there, without replacing the entire valve assembly. I knew going into this project that the Danco escutcheon was plastic (why that even matters to anyone I have NO idea…did you plan on bragging about your metal escutcheon or something???), and I understood this is a generic kit that is meant to update a few different Delta models, therefore some compromises may have to be made.
Secondly, I am not a professional plumber or contractor. I'm just a weekend warrior DIY'er type, with what I would consider "slightly" better than average mechanical skill and problem solving ability.
That being said, I had no problem getting this kit to install and work properly. After reading some of the problems people had, I will have chalk that up as installer error. The escutcheon plate, adapter, gaskets, sleeve, and dome/dome nut went on perfectly. Escutcheon sat flush on the tile, however I did have to use my old Delta escutcheon screws because the supplied screws are 1/4" too short. Due to the grout lines, there are tiny gaps that needed to be dealt with. I used some clear silicone to seal it, which is common practice anyway (DUH!!). The plastic white threaded grommet on the dome assembly needed to be tightened down quite a bit to prevent leaks. There is a special tool made for that, I happened to have one handy since I had just replaced the springs and seals inside the valve assembly. Not sure what it's called, but it came with the seal repair kit. I tightened it down so there was adequate tension on the ball, which eliminates a problem others have commented on in different reviews: the handle being loose and drooping down. HELLO!! It isn't Danco's fault you couldn't figure out that tightening up the ball keeps the handle from drooping! At any rate, the handle adapter went on easily, however I worried it would wiggle loose over time, so I used Locktite thread locker (the blue kind) on the set screw. Same for the handle set screw. I also used some clear silicone on the end of the handle adapter to make sure it didn't wiggle and felt solid. Turned on the water, checked for leaks. Nope, not a single drip. Been using this shower daily for a week and have not had a single issue.
Overall, I think for the price, this kit is a good deal, and a great solution, considering the alternative is spending a few hundred $$$ on a new valve kit. I think the fit and finish are fine. Yes, the escutcheon is plastic, but its not the floppy, bendable kind. It's solid and well painted. It actually looks metal when its up on the wall. Nobody will ever know but you. The handle is heavy and metal, as is the sleeve and dome. I paired this up with Danco's tub spout as you can see in the photo. I did have to use an adapter plate on the spout (also made by Danco) because there was a 1/2" gap, but it all turned out well.
August 15, 2013
Rated 4.0 out of 5.0 by dad Delta bath accessory
I have not instated it yet, it is part of a make over of the guest bathroom. It will add value to my home and will be functional and add charm.
January 6, 2016
Rated 4.0 out of 5.0 by Thom Good replacement for Builder grade replacement shower handle
Easy to install had all the right parts and looks great.
June 16, 2015
Rated 5.0 out of 5.0 by cmccrkn Beautiful and high qualityi bought this to update
I bought this to update a 60s vintage tub with Delta 212 faucet and it worked flawlessly and looks gorgeous. Yes the escutcheon is plastic as the others said but it's a very good quality, stiff part with metal plated finish that looks like a metal part when installed. Making the part from metal would have been unnecessary. The handle adapter fit like a glove and I have no idea what the other reviewers encountered but for the 212 it was a perfect fit. So if you have the 212 faucet this is a great way to make it look new and up to date.
February 2, 2013
Rated 1.0 out of 5.0 by janc1947 Should not be called "universal"
This certainly should not be called "universal" since it does not fit my bathroom faucet. My plumber told me to order this based on the information provided; however, the size is wrong for my installation and many parts are plastic. This item should indicate that it only fits 1" size faucets and not the larger faucets. It is definitely NOT universal.
September 30, 2014
Rated 5.0 out of 5.0 by Harju Easy as pie
Easy as pie to install. IT saved me money not having to replace the whole assembly.
December 18, 2014