DBHL Mechanical Pop-Up Drain Assembly-H759PB-3 at The Home Depot
Discontinued

DBHL

Model # H759PB-3

Internet # 100342744

Store SKU # 701157

Mechanical Pop-Up Drain Assembly


DBHL Mechanical Pop-Up Drain Assembly
 

This item has been discontinued.
The Home Depot no longer carries this specific product.

$31.37 / each
Loading...

PRODUCT OVERVIEW

Model # H759PB-3

Internet # 100342744

Store SKU # 701157

The DBHL Mechanical Pop-Up Drain Assembly features a polished brass finish to match many home interiors. This assembly has a 1-piece design and can be used in lavatory drains. Made of 20-gauge brass.

California residents: seeProposition 65 information

  • Sink stopper has a polished brass finish
  • 1-piece assembly
  • 1-1/4 in. size
  • For use with lavatory sinks

SPECIFICATIONS

Assembled Depth (in.)  1.2 in  Assembled Height (in.)  1.2 in 
Assembled Width (in.)  1.2 in  Color Family  Brass 
Manufacturer Warranty  1 YEAR  Material  Other 
Number of Adjusting Holes  6.0  Plumbing Part Type  Pop Up 
Returnable  90-Day 

CUSTOMER REVIEWS

Rated 2.4 out of 5 by 5 reviewers.
Rated 4 out of 5 by not bad, but installation instructions lacking Most complaints appear to be related to installation and a lack of awareness that there are 3 pieces to the drain assembly : flange/body/tailpiece . Here is how to do it : Remove stopper. Unscrew tailpiece from body. Apply a bead of plumbers putty to underside of flange. Unscrew flange from drain body (carefully, to avoid removing putty). With a finger, slightly increase the gap between putty & flange threads. Rotate the gasket, washer & nut towards the bottom of drain body. Wrap 3 turns of Teflon tape around the upper threads of the drain body Hold flange with putty over the sink drain hole. Push drain body up through the hole as far as you can. Thread drain body onto flange (being careful with the putty underneath). Rotate drain body so stopper rod hole faces the back of sink. Push flange evenly down into sink drain hole. Rotate nut to raise gasket & washer. Tighten until flat upper surface of gasket is in contact with sink (be careful not to overtighten). Wipe off excess putty around flange. Apply pipe sealant to tailpiece threads. Hand-tighten tailpiece into drain body and wipe off excess sealant. If tailpiece is connected to 1-1/2 inch PVC fitting, be sure to use a reducing washer on the tailpiece. October 30, 2013
Rated 2 out of 5 by Product leaks I bought four of these with a chrome finish. All of them leaked between the smooth tube and larger rough sleeve on the bottom - was able to seal with silicon sealer after installation. Two leaked through the threads on the brass nut - had to take apart, apply teflon tape and reassemble (this was after I'd installed so had to remove and reinstall). January 12, 2012
Rated 4 out of 5 by Have to seal the bottom tube with thread sealer After fighting this for quite a while, I realized that you have to seal the threads from the bottom tube to the upper assembly. I did not notice that the bottom tube unscrews from the top until after the entire thing was installed. I am not a plumber, and a set of instructions would have been very beneficial. The Delta that it replaced did not have a separable tube and I did not notice until on my way to return it, because I was sure it was defective. I was wrong, and put thread sealer on it and it was fine. Teflon tape did not work. Use thread sealer. April 7, 2013
Rated 1 out of 5 by Leaked I also bought this unit and it leaked between the pvc pipe connection and the metal tube extending down from the top. January 17, 2012
Rated 1 out of 5 by LEAKS LEAKS Very difficult to seal fine thread connections. I had to redo my installation three times. I did finally work! February 22, 2012
1-5 of 5

SHIPPING AND DELIVERY OPTIONS

Standard Shipping includes delivery by small parcel service. Processing time varies by product.


If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.