Model # DWARA50

Internet #203867866

Store SKU #740286

DEWALT Right Angle Drill Adapter
0885911320207

DEWALT

Right Angle Drill Adapter

  • Enables you to access tight and hard-to-reach spaces
  • Accepts any 1/4 in. hex shank accessory
  • Lightweight and easy to use
$14.97 /each

Frequently Bought Together

Product Overview

Get increased productivity and versatility out of your drill with the DEWALT Right Angle Drill Adapter. Use it with both corded and cordless drills. Use it to get into tight and hard-to-reach spaces.

  • Enables you to access tight and hard-to-reach spaces
  • Accepts any 1/4 in. hex shank accessory
  • For use with most drills - corded or cordless
  • Lightweight and easy to use

Specifications

Dimensions

Details

More Products With These Features

Search

Customer Questions & Answers

does it have a handle so that i can apply pressure in the direction of the screw?

Asked by: Kyle
As there is no handle on it, you need to get your hand on the back of the unit to stabilize it, especially if you are using a spade bit with a threaded tip in a constricted area - it can twist the drill right out of your grip. I found I had more control when using this when I attached the accessory handle to my drill. I could see, however, jerry-rigging a handle for this unit to make it even more stable.
Answered by: Jack
Date published: 2017-02-07

Is the 90 degree attachment heavy duty enough to hold up to drilling multiple 3/4 inch holes through 2x4s?

Asked by: John
ABSOLUTELY! I just did it to run some low voltage wiring from my basement up into the walls above. I had to get deep into the rim joist to drill through the subfloor so that it would get into the wall above. I used the 3/4" bit from these stubby bits: http://www.homedepot.com/p/Bosch-Daredevil-Stubby-Length-Spade-Bit-Set-3-Piece-DSBS5003/203274579 This thing was worth its weight in gold.
Answered by: Matt
Date published: 2017-03-07

Can we use this with 1/2 inch drill bit

Asked by: SR
only if the bit has the adapter end on it for 1/4 inch. I would not use it with that large a bit. Probably not designed for that amount of torque.
Answered by: sand
Date published: 2017-04-07

Does this adapter accept nut drivers as well as screw tips?

Asked by: Mike
It will accept any bit with a hex shank, so if your nut driver has a hex shank it will work.
Answered by: Jack
Date published: 2017-03-02
  • y_2017, m_4, d_23, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_13
  • loc_, sid_203867866, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 17ms
  • QUESTIONS, PRODUCT

Customer Reviews

Right Angle Drill Adapter is rated 4.5 out of 5 by 184.
Rated 3 out of 5 by from I'd recommend this for light duty projects like screwing into tight locations or maybe drilling s... I'd recommend this for light duty projects like screwing into tight locations or maybe drilling small holes. I tried using it for boring holes in framing with a spade bit to run some cabling and the gears stripped after the third hole.
Date published: 2016-12-23
Rated 3 out of 5 by from there is a newer model of this. DWARA100. It has a magnet to hold the screws. It is supposed to b... there is a newer model of this. DWARA100. It has a magnet to hold the screws. It is supposed to be 5x more durable.
Date published: 2016-11-26
Rated 5 out of 5 by from Great tool Well built, priced a little less than the others. Bought to replace a tool that failed under heavy abuse. This finished the job intact. It is primarily for a close quarter bit driver but I used it to drill into aluminum with a chuck and 3/8" drill bit. Tough little tool, well worth he money
Date published: 2016-12-06
Rated 4 out of 5 by from Note: The right-angle adapter is not a chuck based attachment. It is basically a socket for screw... Note: The right-angle adapter is not a chuck based attachment. It is basically a socket for screw bits, etc. As such, I found it difficult to find a drill bit which would be accommodated in such a small space. Otherwise, it works well and provides the needed functionality.
Date published: 2017-01-31
Rated 2 out of 5 by from Works as well as my flexible shaft bit holder. Would have returned it but I can imagine scenarios... Works as well as my flexible shaft bit holder. Would have returned it but I can imagine scenarios where I cant reach to bend the flexible.
Date published: 2017-01-31
Rated 4 out of 5 by from Very good value for the price, particularly for driving screws. I also use it to occasionally dr... Very good value for the price, particularly for driving screws. I also use it to occasionally drill holes into the sides of studs to run electrical cables, using spade bits. This would benefit greatly from the addition of a removable side handle to improve the stability. Still, it's a life-saver if you don't want to either rent or invest in a right-angle drill. It's a snap to use, just chuck it into your standard drill as you would any drill bit or driver bit. Note that it's not suitable really to install into an impact drill, as the impacts will not be transmitted to the bit installed in this attachment.
Date published: 2017-02-06
Rated 5 out of 5 by from I bought it because I have had a need for this in the past. If and when I use it, then you can as... I bought it because I have had a need for this in the past. If and when I use it, then you can ask me how I like it. Thought I would be ahaed of the game for a change!
Date published: 2016-12-27
Rated 5 out of 5 by from This thing is awesome! I needed to drill some holes for low voltage cable in the basement. I ha... This thing is awesome! I needed to drill some holes for low voltage cable in the basement. I had to get pretty deep into the rim joist to drill upward through the subfloor, bottom plate, and into the wall. Using a stubby spade bit (which has a 1/4" hex shank so it fits right into this adapter) I was able to get just far enough in so that the holes would end up in the wall in the floor above. The right tools make a job easy, and this was definitely the case here. Had I not had this adapter I couldn't have done this job.
Date published: 2017-03-07
  • y_2017, m_4, d_24, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_184
  • loc_, sid_203867866, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 19ms
  • REVIEWS, PRODUCT