Rated 3.8 out of 5 by 12
Rated 1.0 out of 5.0 by Mike Missing parts!
I had to make additional trips to HD and explain the missing hardware. My customer was disappointed in the delay and our choice for a shower door.
August 16, 2016
Rated 3.0 out of 5.0 by Raybo Shower rails and door comination-leaks
If the shower head is pointed anywhere near center or towards the door, you will have water on the floor from the splashing down the door into the bottom rail and out on to the floor. I had to wipe the floor up everytime until I pointed the shower head towards the wall. It made it awkward and uncomfortable. The doors should be about 1/2 inch longer and it would stop this problem. and you cant jsut shorten the side rails as then the doors wouldn't fit in the track on the bottom rail.
April 19, 2016
Rated 1.0 out of 5.0 by Jayleighh Terrible quality
Purchased this item for my contractor install shower doors. When he took it out of the box, the whole thing was bubbled and rusted. Very inconvenient to send him home and now I have to box it back up to return it.
August 30, 2016
Rated 4.0 out of 5.0 by Marshmallow Missing parts
I'm generally happy with the product however parts (two rubber bumpers) were missing from the box. I was able to complete the installation and have emailed Delta to see if they can send me the missing parts. I may revise this review depending on their response.
August 13, 2016
Rated 5.0 out of 5.0 by ColdBlue Very Attractive Shower Door Track Assembly
Very good instructions. Filing the radius for the outside bottom corners a must for a nice fit & finish. I found it easier to cut the top and bottom sections with a metal cutting Roto-Zip than a hacksaw. Used lots of masking take to keep the nice chrome from being scratched. I used padded C-Clamps and saw horses to hold the parts steady while cutting. This made the cuts much easier and less stressful. Measure twice and cut once.
August 2, 2016
Rated 4.0 out of 5.0 by hpiguy Quick Installation, Excellent Directions, All in One Kit
I have to say that the three part shower door system by Delta is really what the DIYer is asking for when putting in a new shower door, or as in my case, replacing a 30 year old sliding door assembly on an existing tub surround.
The track/frame assembly arrives in one slender box, with all the hardware you'll need and a very nice set of directions that guide you step by step to ensure success.
When you unpack it, you'll notice the quality metal extrusions and the thickness/durability of the material. It cleans up to a nice shine after install. You have the choice of using the beaded/rolled design facing out as I did (see pictures) or the completely smooth side of the top track to match your tastes. Since the top track just rests on the sides, if you change your mind later, it can be swapped around as well.
After you remove the original doors and tracks and clean the old caulking off, expect to spend about 2 and a half hours from beginning to end assembling the tracks and securing them to the tub surround. If you haven't done this type of work before, allow yourself a half day (4 hours) at the most. Take your time, it pretty much falls into place when you follow the steps.
The only parts that would challenge a beginner would be cutting the top and bottom pieces to fit the width of your particular shower. If you have a good hacksaw with a quality blade, this will go much easier. If you have a power miter saw, this step takes mere moments to accomplish.
The sides install quickly and easily with the holes predrilled in the jambs making locating new holes in the side of the shower a snap.
The top track system snaps into place over the jambs and the glass hangs onto the top track quickly and without any struggle. The glass slides effortlessly on the well grooved track. Totally silent with no sticking. The bumpers and guides make sure the glass stays in place in the tracks and doesn't bang around.
I'm recommending this to all my friends that want to install new shower doors. Don't wait any longer, you can't go wrong with this sliding shower door system! Start designing your new doors today.
July 27, 2013
Rated 3.0 out of 5.0 by damutt Cutting to size is Difficult
Per the instructions given, using a fine tooth hack-saw and a miter box to cut the track is not as easy as illustrated. The track moves as you're cutting it because the miter box is not deep enough to hold the height of the track, even when you turn the track sideways. If you're lucky, you'll be able to re-cut or file the end you've tried to cut correctly. If I ever do this again, I'll ignore the instructions and take my chances with my reciprocating saw instead of the hack-saw. Good LUCK !
April 19, 2014
Rated 5.0 out of 5.0 by Nate Easy as it looks.
Easy to install. First set of enclosure took about 3 hours. Second took 2 hours. You may have to shim the top to get the track level as the tub is not level. Shim before you caulk. Very happy with the end result and I am a critic of most products.
March 18, 2014