Rated 4.4 out of 5 by 5
Rated 3.0 out of 5.0 by skaizun Issues prior to installation
I wanted to put a shelf in my garage, and thought that this bracket would be perfect, but, I had issues with it, which made me cancel my plans.
It is quite heavy and sturdy, so, I have no doubt that it would have done the job, at least for light loads. And, for the record, the actual size of the bracket is 9-1/2" x 7-3/4", excluding the edge of the rounded 90-degree bend (not unusual, since a "two-by-four" is rarely exactly those dimensions).
I was disappointed that it didn't come with the necessary screws/hardware, whose sizes are listed on the information decal (see photo).
I was also concerned that the supporting arch was spot welded through the bracket (see photo), rather than having it molded as a single unit at the forge. The information decal indicates that it has a 600-pound limit, so, if I used three brackets, the load-per-bracket would be significantly reduced, and I wouldn't have put anywhere near that much weight on the shelf, regardless. But, I didn't want to take the chance of a bad weld causing it to collapse (the cantilever effect probably would have prevented that, but, I didn't want to risk it).
Thirdly, although the one screw hole at the bottom would have worked fine, the two holes at the top were very close to the edge of the wood it would have been connected to (the attached photo doesn't quite capture that), and I was concerned that a misdrill or weight shift could cause the screw to go through or pop out the sides of the wood, thus damaging the wood. The mfr could have put one hole at the top and another above where the arch meets the bracket (granted, it would have been a little difficult to use a screwdriver, but, a hex head screw would have easily worked with a ratchet wrench), and it would have eliminated the two-ear-at-the-wood-edge issue. Even if I had thicker/wider wood, the other two concerns, above, were off-putting.
For these reasons, I decided against using it in the garage. There is the potential for using them in a couple of closets, whose sixty-year old shelves' wood frame supports are beginning to buckle, but, the wood is not exposed (behind drywall), and I would have to risk using drywall anchors to make the heavy brackets secure, which I'm not willing to do (i.e., if I misdrill or if there is an issue with crumbling drywall, I would have to fix the hole and find another location for the bracket); also, the heavy-duty brackets would be overkill for the closet. I'll probably go with a shelf-track system (see photo) for both the garage and closets. For the record these brackets may not be for use where aesthetics may be an issue, as they are not "pretty".
October 3, 2015
Rated 5.0 out of 5.0 by Terry Very sturdy
Cannot go wrong with them heavy duty shelf brackets. I had them installed in my kitchen. And it used to carry pretty good amount of load without any issues. These ones are very sturdy (and heavy too). But would fit very nicely. It does have a pretty low profile. Would fit a garage location perfectly. Definitely recommend this bracket, especially if you want to put up a shelf to carry heavy items.
March 8, 2016
Rated 5.0 out of 5.0 by tilepainter the best bracket for any project
These are super-heavy duty brackets, thick steel and solid welds. They're strong enough to hold anything in the garage, yet also good-looking enough to use in the house, which is where I plan to use them. And the price is certainly right, you can pay this much for garage-ugly, or flimsy, and these are neither. One side is longer than the other, and either can be put against the wall, which gives you options. The back sides are flat, and so will be much less marring to the wall that many other brackets, especially the adjustable track type, which leave ruts in the wall when you take them down. These are great for just about any shelving project, and cheap enough that it doesn't matter if they are total overkill.
October 9, 2015
Rated 5.0 out of 5.0 by Dolce1450 Durable product
Decorative but durable. Exactly what I was looking for.
December 29, 2015
Rated 4.0 out of 5.0 by DaneDame Strength plus style in your garage
I'm in the process of upgrading storage in my garage, so I opted to go for a set of these heavy duty shelf brackets in a satin nickel finish-- I needed brackets for shelving to hold some of my heavier tools and supplies, and I like the look of these brackets. The finish itself isn't top grade, but the design is certainly a step up from traditional garage shelf brackets.
The real value of these brackets, in my opinion, lies in the fact they have a load capacity of 600 pounds-- way more than my needs call for, but a great feature for peace of mind when stowing some of my heavier tools. A great set of brackets for the price.
April 1, 2015