Rated 3.3 out of 5 by 40
Rated 1.0 out of 5.0 by HearMeRohrer Outlet/Switch Plate Cover Sticker Does NOT Adhere! JUNK
I am an avid Upcycling Crafter; I make awesome stuff out of other people's junk. So when I say this stuff is an epic failure, know... This stuff is 100% WORTHLESS. It didn't adhere to any of the backs of our typical, plastic, Cover Plates no matter how long (>1/2") or short (1/4") we 'over cut' it. Funny that I had cleaned each cover plate w/Dawn dishwashing soap and then with white vinegar to ensure all were free of any oils, dirt, etc. before attempting to cover...as my husband insisted it was totally unnecessary and I was wasting time. I set them to 'dry out' for 15 mins, and NOT a single sticker stuck to the back of the cover plate once folded over. Broke out the ModPodge, Locktite Super Glue, Gorilla and a few credit cards. And with both of us pressing firmly down on the credit cards over large area of sticker for a good 1.5mins once glue was applied, still EVERY single sticker cover popped off backside of every cover plate after less than 1 min., no matter which additional adhesive we used.
Wasted 4 sheets of this @ $$38 and ended up throwing it all in the trash. I am writing the company directly next. RIDICULOUS, PATHETIC, JUNK!
September 15, 2016
Rated 4.0 out of 5.0 by Don Fine Product
Rigid nature of product does not allow easy folding of vinyl to secure it to the back of plate. It also causes a crease and or wrinkles to form in screw hole. Over all product does as advertised. Other than the items mentioned the product looks great.
May 17, 2016
Rated 3.0 out of 5.0 by LebanonPACustomer Looks Pretty Good, Difficult to Work With
The final product looks pretty good, but you must take your time and follow the directions and use a sharp exacto knife or razor. Leave a little more on the sides than the directions say to make sure the wrap folds around the back nicely. My biggest complaint is that the product doesn't adhere well to the back side of the outlet cover. Even after folding tightly and pressing for several minutes the product doesn't want to stick to the back properly. I think Fasade should offer covers that match panels instead of this product. All in all it matches the decorative panels and looks pretty good. We'll see how long it holds up.
July 29, 2013
Rated 5.0 out of 5.0 by Jessie vinyl peel and stick oil rubbed bronze outlet cover
I have used this product before and have been very satisfied with it. Service from Home Depot
was good as always.
April 19, 2016
Rated 4.0 out of 5.0 by ProfessorShadow Great Idea, but...
I believe the intent of the product is an easy cover to make your outlet cover blend in. Which they would earn a 5~Star.
The part where you bend the "Stiff" material over to cover the sides is a 50-50 proposition. Because the material is a bit thick I needed to add a touch of glue to hold the edges down.
September 30, 2014
Rated 1.0 out of 5.0 by Micky Product did not stick
The vinyl did not stick to the switch plate. I tried to use sand paper to roughen the surface for the second try. It did help some but not around the edges of the switch plate.
February 24, 2016
Rated 5.0 out of 5.0 by Linda Brushed nickel outstanding
Light weight, looks great. Make sure your square footage is correct, maybe order one or two more pieces of backsplash to cover for mistakes.
February 16, 2016
Rated 5.0 out of 5.0 by DKK13 Easy to work with and it cuts with a scissor!
This was the perfect finish to our project. I was afraid it would look like cheap contact paper, but that was far from true.
July 19, 2013