Flotec 40/60 Pressure Switch-TC2153 - The Home Depot
Message to Our Customers


Model # TC2153

Internet # 100177985

Store SKU # 876673

40/60 Pressure Switch

Flotec 40/60 Pressure Switch

This item has been discontinued.
The Home Depot no longer carries this specific product.

$28.45 / each


Model # TC2153

Internet # 100177985

Store SKU # 876673

Store SO SKU # 1000896074

The Flotec Pressure Switch can be used with submersible pumps or as a replacement switch. The switch turns on at 40 psi and off at 60 psi. And can be adjusted to 30/50 or 20/40 psi.

  • For use with water-supply systems
  • For use with submersible well pumps or as a replacement switch
  • Turns on at 40 psi and off at 60 psi
  • Adjusts to 30/50 or 20/40 psi

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.


Assembled Depth (in.) 
4 in 
Assembled Height (in.) 
4 in 
Assembled Width (in.) 
3.75 in 
Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
Brand compatibility 
Flotec, Parts2O 
Product Weight (lb.) 
0 lb 
Warranty / Certifications
Manufacturer Warranty 
90 Days 


Rated 4.6 out of 5 by 18 reviewers.
Rated 5.0 out of 5.0 by best ever 40/60 Pressure switch i ever bought. it was easy to install I did it less then fifteen minutes. December 17, 2014
Rated 5.0 out of 5.0 by A quality product In stock, with a good price, with great quality and easy installation. December 10, 2014
Rated 1.0 out of 5.0 by Short lived Switch failed in the run position after 17 months. A year warranty on something that should last a but forever is not worth much. Pump was running full time. Had over 120 PSI in the system. The gauge was pegged I am glad that the weak link in my pluming was in a unfinished space near a drain and not the pressure tank or in a wall upstairs. (The previous switch lasted 23 years. It failed when the diaphragm devolved a small leak and caused corrosion on one of the contacts resulting in no electrical connection.) The cause of this switches failure is the part that rests against the diaphragm and transmits the force of the water pressure to the switch. It is a disk with two legs bent from the same piece of metal. Both of the legs are and has always be over bent. (>90 degrees) One is bent more than the other. This shows on the wear pattern of the contact points. Over time it the wear caused one of the legs to slid off it's contact point. With the legs at opposite sides of the diaphragm and the disk not engineered to move parallel with out bot legs in contact little (well less than half) of the pressure was transferred to the switch and the pump would not shut off. With most manufacturing defects if there is one most likely there are more produced at the same time. It is all so possible it has been found and corrected by now. November 23, 2013
Rated 5.0 out of 5.0 by Quick Install, restores performance. Easily installs as direct replacement to existing pressure switch on whole house well pump. Has feature to adjust the cut in and cut out, however 40-60 was where I need mine at, so I did not change it. Restores the water pressure to past performance.......the old switch had not completely failed yet, but the pressure was varying from 20-60psi and the kitchen faucet and garden hoses were just about worthless. The cut in and out pressure works so uniformly now, the pressure is consistent just like city water pressure. March 17, 2012
Rated 4.0 out of 5.0 by Works Have used this pressure switch before. Lasts years. It can time to adjust properly, but all switches are that way. October 9, 2013
Rated 5.0 out of 5.0 by Well constructed, packaged and directions for the novice were easy to follow. Switch was well packaged and fittings were in separate plastic bag for either type of tube fittings. Was constructed very well and electrical wiring connectors were easy to wire up. There are two ground screws for auxiliary equipment needing to be switched on with the pump ( ie:chlorinator). The cover mounts tightly and wire tubing connects to standard EMT 1/2" openings. The adjuster springs for on/off settings still must be adjusted with the power off as shorting is possible with wrench near terminals, however there is a small ridge of plastic that offers more protection than many other switches. Directions were easy to follow and adjustment springs were lubricated for easy settings. March 13, 2012
Rated 5.0 out of 5.0 by works perfect Simply remove old switch and replace with new. if unsure remove cover, snap pic with smart phone on where old wires where located. July 22, 2014
Rated 5.0 out of 5.0 by easy to install I needed something quickly and this switch was in stock and installed easily and works great July 19, 2014
  • 2015-05-22T11:20:25.984-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_18, tr_18
  • loc_en_US, sid_100177985, prod, sort_default
2 >>


Standard Shipping includes delivery by small parcel service. Processing time varies by product.

If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.