Rated 3.9 out of 5 by 47
Rated 1.0 out of 5.0 by SteveP Did not last
I installed three of these to replace the OEM bottoms that were failing after 13 years of use. Two of three failed after about 1 year where the fins started to tear off. The one that did not fail is on an interior door protected from the elements. I decided to track down the OEM bottoms and install these to replace the failing Frost Kings. I believe the key difference is that the OEM did not manufacture these out of cheap PVC. Save yourself the time and trouble and find quality bottoms elsewhere.
May 29, 2016
Rated 5.0 out of 5.0 by diesel51 Bugs no more
I purchased an older home and had the usual inspection. A few days after moving in the bugs moved in with us. Everything that could crawl came in. I called a home pest service. They were all too willing to have me sign an expensive pest control contract.
I looked around and the door had torn stripping on the bottom.
Looking online, I found the stripping in the right size for the door and it was in stock. I went to the store and within an hour the door and bug problem were over. Very easy to install.
January 19, 2016
Rated 2.0 out of 5.0 by Handyman Did not last!
This replacement bottom did not last very long, in my opinion. I have a 32 inch pre-hung Stanley steel door purchased from Home Depot in 2002. The original lasted about 8 years. I replaced it with after-market universal fits several times. Found this one at HD and gave it a try. I had to trim to size, which wasn't at all difficult with a sharp utility knife. It seemed to fit good with no drag or binding. In other words, it just "touched" the threshold as it should. It only lasted 2 months until one thin sweep came off, followed by another the next week. Then about three weeks later the rounded "outside piece" peeled off. Gotta due it again with el Nino on the way toward my west facing door!
January 4, 2016
Rated 5.0 out of 5.0 by Fender4Ever Door Sweep Replacement
Great product, perfect fit for my 1.75" X 36" wide entry door. Although it is listed as a replacement for a Stanley steel door, it worked perfectly with my 6-panel, non-metal "no-name" door. The original sweep that came with my door had deteriorated from the Florida sun. I ordered this one because it had the "bulb" or "tube" construction that fits up against the door stop, like my original sweep, and works well to keep out the critters.The instructions were simple to follow, and the product installed in a matter of minutes. I'm happy!
May 31, 2016
Rated 5.0 out of 5.0 by GH Stanley door bottom gasket (weatherstrip)
Perfect replacement. Instructions say to take the door off the hinges but it isn't necessary. All you need is a screw driver to pry the old strip off.
May 31, 2016
Rated 3.0 out of 5.0 by Bob Door sweep
This was a Stanley replacement part for my door. Fit and mounted properly on the door, but is now difficult to open or close due to
Different design of seal.
As time goes on it is seating and getting better, but not like original seal was when I bought door.
May 10, 2016
Rated 4.0 out of 5.0 by SVBill Worked with some persuasion, slightly different from 20-year old verison it replaced
I installed our Stanley steel door some 20+ years ago. The old door bottom had become brittle and broke in several places. After cutting this one down to 32", I was able to install it by taking the door off and using a hammer to tap it into place.
I was hoping to avoid removing the door since I could remove and replace the old door bottom with simple hand pressure under the door. The difference in fit is because of the shape of the kerfs and the location of the barbs on the fins.
The kerfs on the bottom of the door are V-shaped with a narrow straight slot at the point of the V. The old door bottom has the barbs positioned closer to the tip of the fins, so they would engage the narrow slot of the kerfs more easily. The barbs on the new door bottom are positioned farther down the fin, so in order to get them to engage the narrow slot of the kerf, I had to tap firmly with a hammer along the entire length of the door bottom.
It seems firmly attached, but if it does come free, I'll just repeat the process and add a few staples to keep it in place.
April 10, 2016
Rated 4.0 out of 5.0 by Jerryswfla Out with the old...In with the New!!
Open door and pull old strip down and out of slot in bottom of door..place new strip in slot oñ door bottom and and tap up into place with a hammer. Trim off even with edge door with a utility knife. Close door and check seal from the inside!
February 9, 2016