Model # MSG-301

Internet #202585314

Store SKU #307160

Gardner Bender Low Volt Wire Staple Gun for Heavy Duty and Stainless Steel (Case of 4)

Gardner Bender

Low Volt Wire Staple Gun for Heavy Duty and Stainless Steel (Case of 4)

$19.97 /each

Frequently Bought Together

Product Overview

Low-Voltage Staple Gun offers heavy-duty stainless steel construction and secures wires up to 1/4 in. in diameter. Gun features a safety handle to ensure staples don't release unintentionally. This stapler gun is designed for use with alarm, speaker, thermostat, A/V and computer network wires. 2 sizes of staples available; 5/32 in. (4 mm) Model #MMS-3101 and 1/4 in. (6 mm) #MMS-3102.

California residents: see   Proposition 65 information

  • Use for stapling low-voltage wiring such as alarm, bell, intercom, security, speaker, thermostat, A/V and computer wires
  • Resists damaging the wires and interfering with the electrical current
  • Heavy-duty stainless steel design
  • Compatible with 5/32 in. MMS-3101 and 1/4 in. MMS-3102 staples
  • Safety handles for compact storage
  • Easy loading
  • Fasten wires up to 1/4 in. of diameter




Warranty / Certifications

More Products With These Features


Customer Questions & Answers

1 Question2 Answers

Customer Questions & Answers

Low Volt Wire Staple Gun for Heavy Duty and Stainless Steel (Case of 4)
Low Volt Wire Staple Gun for Heavy Duty and Stainless Steel (Case of 4)

Ask your questions. Share your answers.

Clear Search Term
2 answers

need to replace pusher spring in staple track.

This question is from Low Volt Wire Staple Gun for Heavy Duty and Stainless Steel (Case of 4)
Asked by
new york
Read all my Q&A
August 24, 2014
need part number for pusher spring to advance staples.
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
Waterville, ME
Read all my Q&A
Home Improvement Profile: Professional
January 6, 2016
Contact the company and nicely request a replacement part. Oftentimes, manufacturerers will even forgo shipping/mailing fees when contacted directly when parts are otherwise difficult to locate.
Try here with attention toward 'Contact'...
Detail the tool name and model/numbers with a clear explanation of the part needed.
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Read all my Q&A
Home Improvement Profile: Other
August 24, 2014
Gardner Bender does not offer replacement parts for this staple gun. If the tool is still under warranty and the spring malfunctioned due to a defect, GB will replace the whole tool.
0out of 1found this answer helpful.
Was this helpful?helpful0unhelpful1
1 of 1
  • 2016-10-22 T19:06:44.011-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_202585314, prod, sort_default
1 of 1
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 182ms

Customer Reviews

Rated 3.6 out of 5 by 7 reviewers.
Rated 1.0 out of 5.0 by Failed after 10 staples Failed in the first day of use. Did 10 staples without a problem. Every staple after that, one leg would go in, the other would double up or splay out to the side. September 26, 2016
Rated 5.0 out of 5.0 by best staple gun i ever bought to staple up speaker wire and christmas lights All the other staple guns I have end up not being a wide enough staple. June 28, 2016
Rated 5.0 out of 5.0 by Reliable and Tidy Installation of Ethenet Cable This stapler with the 1/4" staples made the job of doing a clean installation of a cat5e along a baseboard and up a plaster wall to extend a LAN connection to another room so much easier. Forget about using nail-on staples or tie-wraps with adhesive anchors which are unsightly and don't anchor well to plaster walls. Once installed, the staple is able to hold the cable in place yet with enough room to slide so there is no danger of damaging the cable. I'm looking forward to using this stapler for other low voltage cable runs in my house and garage. February 6, 2016
Rated 5.0 out of 5.0 by Specialty stapler Low voltage wire can often be shorted out to cause disrupted continuity and alot of frustration if fastened with standard staplers clinching the wire's insulation too tightly. This stapler uses shaped staples that cradle the wire without pinching. Garage door openers functioning improperly or intermittently from remote wired buttons can be a cause of pinched low voltage wires due to improper installation. People take shortcuts with the many feet of wire involved with the remote location buttons and safety features. Over the long run, it's worth investing in a proper stapler if hoping to save time and not cause harm to the wiring. This stapler functions flawlessly without jams and I highly recommend it to anyone installing garage door openers, doorbells, Christmas lights(the staples pull out easily with needle nose pliers for removal), and anything else a creative mind can find for the use of the shaped staples. I've even used these, carefully, for holding glass in frames and when fixing the backboards into picture frames by just bending the staple securely. The uses can be many and not limited to just fastening wire low voltage wire. January 6, 2016
Rated 1.0 out of 5.0 by Don't Bother I purchased this item to use when running CAT5e cable. It was not used hard or frequently. Had it about 3 months. One day it would not staple. I thought it was out of staples so I decided to reload. To my surprise it was more than half full. After further examination I found out that a piece that holds the spring tight was broken so the staples would not feed to the front. I liked the way the thing worked, when it worked, so I bought another one. This one lasted about 4 months before the same thing happened. I am now stuck with two boxes of staples almost full and no staple gun to use them in. March 17, 2015
Rated 4.0 out of 5.0 by works well The stapler works very well, I have used more expensive staplers for years and this one performed well October 6, 2015
Rated 4.0 out of 5.0 by Recommend I purchased this staple gun about a year ago and also purchased two other units for other Techs in our company. They have worked without issues and are always in the tool bag. I have probably put 5-6 boxes of staples through the unit without any jams or other problems. If the spring strength was a bit better and could get staples into harder surfaces a bit better, I would give the unit 5 stars. June 27, 2015
  • 2016-10-22 T16:13:55.820-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_7, tr_7
  • loc_en_US, sid_202585314, prod, sort_default
1-7 of 7
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 35ms