Halo 5 in. Air-Tite Remodel Housing-H5RICAT at The Home Depot
Free shipping
Discontinued

Halo

Model # H5RICAT

Internet # 100024856

5 in. Air-Tite Remodel Housing


Halo 5 in. Air-Tite Remodel Housing
 

This item has been discontinued.
The Home Depot no longer carries this specific product.

$14.98 / each
Item cannot be shipped to the following state(s): AK,GU,HI,PR,VI

PRODUCT SOLD Online Only

In Stock

Loading...

PRODUCT OVERVIEW

Model # H5RICAT

Internet # 100024856

The HALO 5 in. Air-Tite Remodel Housing features an Air-Tite design to prevent airflow between the attic and living areas in your home. This remodel housing has a built-in thermal protector that can be covered by insulation and is compatible with Halo 5 in. trim.

  • For use as remodel housing
  • Air-Tite design
  • Thermally protected IC housing which can be covered by insulation
  • Compatible with Halo 5 in. trim
  • Insulation contact (IC) rated
  • UL listed
  • Easy installation
  • Note: Product may vary by store.

SPECIFICATIONS

Airtight  Yes  Aperture width (in.) 
Assembled Depth (in.)  7.25 in  Assembled Height (in.)  7.5 in 
Assembled Width (in.)  10.5 in  Certifications and Listings  1-UL Listed,CSA Listed,IC Rated 
Collection Name  na  ENERGY STAR Certified  No 
Housing depth (in.)  Insulation contact  Insulation contact 
Light Source  Incandescent  Manufacturer Warranty  standard 
New Construction or Remodel  Remodel  Number of Housings Included 
Product Weight (lb.)  1.54 lb  Product Width (in.)  14 in 
Recommended bulb type  PAR 30  Reflector finish family  Aluminum 
Returnable  90-Day  Size  5 in. 

CUSTOMER REVIEWS

Rated 3 out of 5 by 49 reviewers.
Rated 5 out of 5 by Easy to install once you figure out 1 clip I had the same frustrations for a little while trying to push the clips out with my fingers which proved impossible. Then a light bulb went off (no pun intended). The reviewer from 1/28/13 is spot on. There's a little ledge on the clip (under the grey insulating tape) where you can put a flathead screwdriver on it (not under it). Place the flathead on it perpendicular to the little ledge, then hammer it towards the wall of the can, which will push the clip outward. Dont wail away, just firm taps w/ the hammer. Once you have the clip against the can, put the screwdriver under that little ledge and hammer up to lock the clip. Once you get one down you'll realize how simple it is and the rest will be a breeze. September 9, 2013
Rated 3 out of 5 by Check for socket clips The socket had no clips to hold them in. so then I have to by the Halo bezel which is more expensive. October 18, 2014
Rated 4 out of 5 by Good Housing...after you figure out how to install the clips. These are good quality can lights but it took me about five cans before I really figured out how to easily install the clips. You don't need to bend the clips or the housing and there is nothing wrong with the design. The problem lies in the fact that the lower portion of the clip (t-section) has to slide down between the housing and the drywall to properly (easily) lock in place. If you use a 5 1/2" hole saw to make a precision cut, when the housing is pushed up into the hole, there is no space for the t-section of the clip to slide, and this is the reason that it won't snap in place. The easiest way to remedy this is to push the housing up into the hole and get it where you want it, then take a small 90 degree pick and scratch out some of the drywall near the bottom of the housing where the clips go. It doesn't have to be a lot just enough for the clip to slide down. If you do this, the clips will snap down easily and then you can take a flat blade screwdriver and just slide the clip up locking it in place. Also you can buy some #14-3/4" screws to secure the clip to the housing. This makes the installation very secure and I did this as well. I will caution you that the clip has to be slid up in the housing before driving the screw in though. You can't just use the screw to lock the clip down if it keeps popping up. The screw will not hold if you try to drive it into the t-secion of the housing. I found that I damaged quite a bit of the foam when installing these, so I bought some aluminum tape, like you use on sheet metal duct work and put a piece over each clip to make the housing more air tight. You can also use this tape to seal up other areas of the housing. If you get the clips installed correctly, you may not need to bother with the screws as this will be fairly secure. November 9, 2011
Rated 4 out of 5 by You must be smarter than the clips The clips are little bit of a pain if you don't understand how they work. You need to push a flat head screw driver though the insulating tape so that it catches on the small tab under it . Then you need to hit the screw driver with a hammer so as to push the clip out (flush with the wall of the can) and then upward so the clip slides up the slot to lock in place. My dad, who's been a electrician for over 35 years and who has installed hundreds of Halo can was totally frustrated. I'm an engineer though and figured it with a little trial and error. January 28, 2013
Rated 5 out of 5 by Installing as easy as 123 Read all negative comments about the clips. Be patient people, nothing comes easy. I just installed 14 of them. They look great. You just have to figure out how the clips work and next thing you know you'll be on a roll. Try this. Place a flat head screw driver on the gray tape on clip and tap inwards with the palm of your hand or a hammer, then gently hit the clip upward and it will lock in. The trick is pushing the clip inwards and then upwards. Do one clip on one side and then one the opposite side first. then finish the rest. You also want to make sure there is not debris on the other side of the sheet rock as this may prevent the clip from locking into place properly. Do Not hit the clip upward too hard or you will tear right thru it. May 16, 2014
2 3 4 5 6 >>

SHIPPING AND DELIVERY OPTIONS

Standard Shipping includes delivery by small parcel service. Processing time varies by product.


If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.