Free Shipping and BOPIS

Heath Zenith

Model # DW-715-1

Internet # 202209289

Store SKU # 737874

Wired Lighted Push Button - White Finish

This item has been discontinued.
The Home Depot no longer carries this specific product.

$7.97 /each




Model # DW-715-1

Internet # 202209289

Store SKU # 737874

To aid your visitors in the dark, install the Heath Zenith Wired Lighted Push Button. It features a lighted, white bar button in a white housing. This push button surface-mounts with ease.

  • Works with Heath Zenith Low-Voltage chime systems
  • Hardwire to your home's electrical system
  • Lighted, white bar button
  • Body finished in white
  • Surface-mounted installation requires no additional holes be drilled


Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
Batteries Included 
Bell Button Type 
Color Family 
Door Bell Or Intercom Type 
Door Bells 
Electrical Product Type 
Bell Button 
Mounting Style 
Warranty / Certifications
Manufacturer Warranty 
1 Year 


Rated 4.3 out of 5 by 43 reviewers.
Rated 4.0 out of 5.0 by Simple improvement Easy to install even for an old lady like me. A small price for a nice touch to the front entry. September 22, 2015
Rated 5.0 out of 5.0 by Easy to Install The door bell switch was easy to install. Button light is bright and easy to see. Works well September 1, 2015
Rated 2.0 out of 5.0 by Fine button until the light burns out This lighted doorbell button is made in China. It is easy to install, and the light is bright. The bright light should have tipped me off -- in one of the two I bought, the bulb burned out after four months. The bulb is not replaceable, so after it goes, you have a non-lighted button. How stupid is this design! Doorbell transformers have been 24 volts for decades. A good design would have used a bulb rated for a higher voltage, even if that makes slightly less light. If you're an electronics wiz like me, it's easy to remove the bulb and install a white LED in this button. I did this with both buttons, and now I never need to worry about a bulb again. Technical summary: Bright white LED, 1N4001 diode, 1.8K 1/4-watt resistor, all connected in series between the two button terminals on the circuit board. LED current is about 6.5 milliamps. Unsolder the bulb, clean the holes, and solder one lead of the diode and resistor in each hole. Mount all components on the back side (away from the button) of the circuit board. I drilled a #11 hold through the center of the circuit board, and poked the LED through it, securing with two drops of super glue. Connect the remaining lead on the diode and resistor to the LED. June 20, 2015
Rated 4.0 out of 5.0 by great price This works great for a replacement for our broken push button. I have yet to install it so I'm not sure how easy it will be but it seems pretty easy. Cant beat the price! July 14, 2015
Rated 2.0 out of 5.0 by Cheap Button A cheap plastic button. If it isl located in the sun, it will become brittle and fall apart after a couple of years. In my case it stuck on and over heated the chime unit. August 24, 2010
Rated 5.0 out of 5.0 by Simple and it works It's a doorbell push button that lights up, It works you push it the door bell sounds. The price is a little high for a small piece of plastic with a contact. June 2, 2015
Rated 5.0 out of 5.0 by Door bell Ended up an easy installation. Value priced and looks good. May 13, 2015
Rated 5.0 out of 5.0 by ding dong Glad I bought this cheap doorbell button. This is the only one that fit between my Anderson 3000 Storm Door & the framing. This is the narrowest sized doorbell button I seen in the store. Works great. Seems a little cheap in design ruggedness but time will tell. July 22, 2014
  • 2015-10-05T14:26:18.730-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_43, tr_43
  • loc_en_US, sid_202209289, prod, sort_default
2 3 >>