Model # H4850GHVSG

Internet #203497641

Store SKU #762096

Husky Gravity Feed Composite HVLP Spray Gun
0722470273158

Husky

Gravity Feed Composite HVLP Spray Gun

$69.98 /each

Frequently Bought Together

Product Overview

Husky spray guns feature stainless steel needles and precision air caps for reliability and perfect paint atomization. All Husky Spray Guns have the controls located at the rear of the gun to allow comfortable use by left and right hand operators. Husky HVLP (high volume-low pressure) technology provides high material transfer efficiency, eliminates paint waste and requires lower air volume. This Husky HVLP spray gun is the lowest weight gun available and is ideal for high volume paint application for car refurbishing, industrial and woodwork. This gun is not suitable for use with Latex Paint. The gun is easy to clean and comes complete with a cleaning brush set and multi wrench.

California residents: see   Proposition 65 information

  • 600 cc cup
  • Stainless steel needles for ultimate reliability
  • Precision spray cap for perfect pattern
  • Smooth/comfortable trigger pull

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

7 Questions12 Answers

Customer Questions & Answers

Gravity Feed Composite HVLP Spray Gun
Gravity Feed Composite HVLP Spray Gun

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
3 answers

how do i get a operators manual for the gun?

This question is from Gravity Feed Composite HVLP Spray Gun
Asked by
marathon
Read all my Q&A
December 15, 2014
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (3)

Asked by
Antelope Valley, CA
Read all my Q&A
Home Improvement Profile: DIYer
April 18, 2015
Answer: 
Go here, then click on the "PRODUCT OVERVIEW" tab. It will be just to the right on the PDF link
http://www.homedepot.com/p/Husky-Gravity-Feed-Composite-HVLP-Spray-Gun-H4850GHVSG/203497641#specifications
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

March 3, 2015
Answer: 
Pull up the item on THD.com and the manuals are there for download. If not contact THD customer service and they can assist.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
December 16, 2014
Answer: 
On Home Depot's website search for this spray gun. Open the Product Overview tab and the manuals will be on the right side of your screen. I like my spray gun.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
 
2 answers

This states clearly that it is not for latex. Does it work with plastidip or autoflex peelable paint?

This question is from Gravity Feed Composite HVLP Spray Gun
Asked by
Montana
Read all my Q&A
May 25, 2016
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

May 27, 2016
Answer: 
David,
Gun will actually spray latex but it must be thinned per the manufactures specifications. Not sure on the Plastidip or autoflex, but as long as the product pours smoothly or runs smoothly off the stir stick and does not contain any flakes or textured materials it should spray fine. Material needs to be no thicker than pancake syrup consistency to be able to flow smoothly trough the spray gun neck Read More
David,
Gun will actually spray latex but it must be thinned per the manufactures specifications. Not sure on the Plastidip or autoflex, but as long as the product pours smoothly or runs smoothly off the stir stick and does not contain any flakes or textured materials it should spray fine. Material needs to be no thicker than pancake syrup consistency to be able to flow smoothly trough the spray gun neck and spray fluidly and evenly through the spray gun head. Read Less
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

May 26, 2016
Answer: 
This spray gun can be used with oil paints or car paints.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
2 answers

Can this be used for water based polyeurathane

This question is from Gravity Feed Composite HVLP Spray Gun
Asked by
Read all my Q&A
November 30, 2015
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
September 21, 2016
Answer: 
Yes. I have sprayed it several times with good results.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

January 19, 2016
Answer: 
Yes.
0points
1out of 2found this answer helpful.
Was this helpful?helpful1unhelpful1
 
2 answers

can you buy replacement needles, fluid nozzles, and air caps

This question is from Gravity Feed Composite HVLP Spray Gun
Asked by
liberty lake wa
Read all my Q&A
September 19, 2015
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

September 22, 2015
Answer: 
Yes... Call the 800 number in your parts manual and we will direct you to one of our service centers where you can order parts. The parts manual provides a breakdown of the tool and all corresponding parts numbers.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
September 21, 2015
Answer: 
Yes. It comes with a parts list and you can order from Husky. You can order parts through customer service at Home Depot as well.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
2 »
  • 2016-10-31 T01:43:17.376-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_203497641, prod, sort_default
2 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 47ms
  • QUESTIONS, PRODUCT

Customer Reviews

Rated 3.3 out of 5 by 24 reviewers.
Rated 5.0 out of 5.0 by Yes, you can use this to paint furniture I could not find this answer, so I had to figure it out mostly through research and trial and error. Hopefully this review will help someone who is wondering, "Can I use this to paint cabinets or furniture?" The answer is yes - if used with the certain tools and processes. I refinished the cabinets in two bathrooms and also refinished a dresser and dining table recently and everything looks beautiful, but it was a lot of work! Tools: 1.8 horsepower 8 gallon compressor with 5 SCFM at 40 PSI - this is about the minimum air compressor that I think would work for a project like this. You can expect to get maybe 1 light coat on a cabinet door front or maybe a few drawer faces before the compressor will need to refill. If you do not turn it off while spraying, it will basically run constantly. If refilled too quickly too often, it can overheat and stop. This Husky Gravity feed composite air gun - this gun actually comes with 2 tips: 1.4 and 2.2 (yes, the specs online were incorrect, the parts are labelled). I only used the 2.2 and it did a great job with thinned primer (water and oil base) and Benjamin Moore Advance paint (more details on that shortly). It takes practice and I always start with a fresh scrap canvas to get the pattern right and re-familiarize myself with the gun. I cleaned the gun meticulously after each session and also kept the nozzle clean with a rag and thinner between spraying each couple of pieces. In line water and oil separator - apparently it keeps condensation water from coming back into your paint. I used it and had no problems but I could see the water building up in there. 25 foot PVC 3/8 inch hose - I heard some bad things about working with a PVC hose, but it has been just fine for me. Apparently you can lose some power with a 50 ft hose, and since my compressor was right on the edge of having enough SCFM, I went with 25 feet. Also, apparently using multiple quick-connect couplings can decrease power, so I used only threaded fittings with plumber's tape on each connection (with the exception of the one quick-connect on the compressor itself). I also used disposable nylon micro paint strainer filters to keep any sediment or chunks out of the hopper. Paint Selection and Thinning: I used a Ford #4 cup to measure and notate viscosity (measured in time). Generally, if I could get it down to 45 seconds or 1 minute it would spray well through the 2.2 nozzle. I also used a small helix mixer chucked in a drill to really mix the thinner and paint thoroughly, which also seemed to improve sprayability. I did two light coats of primer, either water or oil-based as outlined below. I used a bit of an expensive waterborne bonding primer (acrylic-urethane primer-sealer) which worked as well as advertised. I found that a mixture of 10 oz primer and 2 tbsp distilled water would yield 45 seconds and spray very well. This primer is recommended for cabinet work and has exceptional adhesion. I did two primer coats on each side. The only problem is that any areas with bare wood would "bleed color" through this primer. So, I used a stain-covering oil based primer on bare wood, which is an interior oil-based primer and found that I needed to use 4 tbsp of mineral spirits with 9 oz of primer to get under 1 minute, and then it finally sprayed well, but not as easy to work with or clean up as waterborne options. I used this on any bare wood because, in my experience, it completely stops any "color bleed". This stuff works well but has strong fumes and is extremely difficult to clean out of the gun. For the paint I selected a specialty waterborne interior alkyd - and found that needed 9 oz of paint thinned with 2 tbsp of distilled water to get down to 55 seconds and then it sprayed very easily. This paint product can take a few weeks to cure depending on temperature and humidity. It is recommended for cabinets because it has excellent leveling, cures extremely hard, and looks like a traditional alkyd finish. It really sprays wonderfully. My cabinets appear to be fully cured after 2 weeks in an average of 65% humidity and a 70-90 degree temperature range. I did 2 light coats with this to finish the project, 3 coats on a few pieces for extra coverage. I let each coat dry for at least 24 hours before the next. Technique and Notes: I tried spraying cabinet doors and drawer faces vertically and horizontally. The horizontal method of laying them down is much easier and allows the paint to level out over any small imperfections. They are also easier to transport in this orientation. It was better to do light coats because a heavier coat would run and sag, especially on any vertically positioned panels. I purchased a "paint gun holder stand" and think that it was worth it as well so that I could set the gun down whenever needed. This goes without saying, but 90% of the process is prep work. Cleaning, scuff sanding for adherence, spackling & sanding dents and scratches, and caulking seams will result in a flawless finish. I lightly sanded after the second primer coat with 320 grit to give the finish coat the best possible base. I had no idea how big of a mess this would make. I built a little paint area and backstop in my garage with a fan blowing the outwards. There was paint dust in every corner and crevice of every item and tool in my garage and it took a few full days to get everything cleaned off. I had to shop-vac and mop the concrete floors a few times. A full respirator and goggles are required because the air is filled with actual paint, not just paint fumes. Next time I would build an enclosed air-tight booth with ventilation or do it outside. I would also put everything in trash bags and then seal them as well. September 24, 2016
Rated 1.0 out of 5.0 by Husky (pain) gun May be one of the worst purchases I have made, nothing works correctly, try to save a few bucks and that's what you get. Big waste of time and money. I had to give it one star or the app would not let me move forward to submit. October 5, 2016
Rated 4.0 out of 5.0 by Great Gun Good quality spray gun. you will have to fine tune it when getting started and keep the air compressor pressure adjusted slightly lower than recommended to get the best result. September 9, 2016
Rated 4.0 out of 5.0 by husky gravity gun Works really good painted my street rod w/it. 90 percent of the time its user error that causes a bad paint job not the gun. December 23, 2015
Rated 4.0 out of 5.0 by Specifications Correction I have not used this gun yet. However, I have inspected it thoroughly and wanted to provide an update in case anyone was planning to make a purchase based on the specs here. The gun actually does come with two cap/nozzle sets: 1.4 and 2.2, they are each labeled Otherwise, it appears to be very high quality and looks like an excellent value. I will update the review if necessary soon. Thanks! July 6, 2016
Rated 5.0 out of 5.0 by Arlington, TX This is the handiest sprayer I have ever owned! It is easy to use and clean up. July 5, 2016
Rated 4.0 out of 5.0 by Does good job This was my first experience with a gravity feed, so there was a learning curve. June 14, 2016
Rated 4.0 out of 5.0 by Does a great job at what it is designed to do My husband repairs and repaints antique tractors to sell. This Husky gravity feed spray gun works like a champ for spraying the hood, fenders, body and wheels of the tractor. But for tighter spots and upside down spraying, a bottom feed sprayer works better. This Husky spray gun has a really good feel to it. It has several settings. The controls are conveniently located on the rear of the gun. It produces a fine even spray which helps prevent drips. Best of all, this spray gun is able to efficiently cover more area with less paint. It is easy to clean and even comes with the tools to do it. This gun is NOT FOR LATEX PAINT. All in all this spray gun does a very good job doing what it is designed to do . Buy with confidence. May 19, 2014
  • 2016-10-31 T00:10:12.919-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_24, tr_24
  • loc_en_US, sid_203497641, prod, sort_default
2 >>
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 67ms
  • REVIEWS, PRODUCT