0722470273165

Husky

Model # HDK00600SG

Internet # 203497812

Store SKU # 793334

HVLP and Standard Gravity Feed Spray Gun Kit

$79.98 /each
  • Kit Features: (1) HVLP Spray Gun and (1) Conventional Spray gun
  • Stainless steel needles for ultimate reliability
  • Precision spray cap for perfect pattern

FREQUENTLY BOUGHT TOGETHER

PRODUCT OVERVIEW

Model # HDK00600SG

Internet # 203497812

Store SKU # 793334

Husky spray guns feature stainless steel needles and precision air caps for reliability and perfect paint atomization. All Husky Spray Guns have the controls located at the rear of the gun to allow comfortable use by left and right hand operators. This Husky spray gun kit features both a conventional and HVLP spray gun both with 600 cc paint cups. Husky HVLP (high volume-low pressure) technology provides high material transfer efficiency, eliminates paint waste and requires lower air volume. Both spray guns in this kit are ideal for high volume paint application for car refurbishing, industrial, wall painting and woodwork. These guns are not suitable for use with Latex Paint. The guns are easy to clean and come complete with a cleaning brush set and multi wrench. The kit also includes in-line regulators, extra paint cups and paint filters.

California residents: see  Proposition 65 information

  • 600 cc and 120 cc paint cups
  • Stainless steel needles for ultimate reliability
  • Precision spray cap for perfect pattern
  • Smooth/comfortable trigger pull

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.

SPECIFICATIONS

Dimensions
Air Inlet Size 
0.25 in 
Fan Size (in.) 
1.2 to 9.2 
Product Depth (in.) 
16.73 
Product Height (in.) 
16 
Product Length (in.) 
5.5 
Product Width (in.) 
17 
Tip Size 
1.4mm 
Details
Accessory Type 
Kit 
Air Pressure at Paint Cap PSI 
25 & 50 
Air Tool Type 
Air Sprayers 
Air consumption at recommended operating pressure (CFM) 
Average air consumption @ recommended operating pressure (CFM) 
Feed type 
Gravity 
Housing Material 
Aluminum 
Included 
No additional components or accessories are included 
Interior/Exterior 
Interior/Exterior 
Maximum operating pressure (psi) 
40 
Number of Spray Settings 
30 
Paint Cup Size 
200cc & 600cc 
Paint Sprayers Product Type 
Pneumatic 
Project Type 
Painting 
Recommended operating pressure (psi) 
40 
Returnable 
90-Day 
Tool weight (lb.) 
1.35 
Tools Product Type 
Air Tool Kit 
Type 
HVLP Standard 
Weight, Including Paint Cup (lb.) 
1.35 
Warranty / Certifications
Manufacturer Warranty 
2 Years 

MORE PRODUCTS WITH THESE FEATURES

Price: $50 - $100
Brand: Husky
Review Rating: 4 & Up
Search
38 Questions72 Answers

Customer Questions & Answers

HVLP and Standard Gravity Feed Spray Gun Kit
HVLP and Standard Gravity Feed Spray Gun Kit

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
8 answers

What kind of paint can I use with this kit?

This question is from HVLP and Standard Gravity Feed Spray Gun Kit
Asked by
Brooklyn, NY
Read all my Q&A
January 18, 2014
The description says that these guns are not suitable for latex paints. I am trying to paint interior walls inexpensively - what kind of paint can I use?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (8)

Asked by
Read all my Q&A
December 18, 2015
Answer: 
I just used an interior latex to paint a dresser. Used a thinning solution, sold by HD, and it worked wonderfully.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

March 3, 2015
Answer: 
Almost any type of paint is acceptable. But you need to thin the paint per the paint manufactures specifications. The viscosity needs to be able to pour no thicker than pancake syrup.
+4points
4out of 4found this answer helpful.
Was this helpful?helpful4unhelpful0

Asked by
Read all my Q&A
February 20, 2015
Answer: 
It says no latex. I would use a an airless sprayer you can rent them for not much. This would create to much dust if used on walls and take too long. I would suggest using a 14 inch roller nap with wooster roller frame the mac truck inside airless sprayer outside.
-1point
1out of 3found this answer helpful.
Was this helpful?helpful1unhelpful2

Asked by
seattle, wa
Read all my Q&A
February 15, 2015
Answer: 
I just submitted a post about using this gravity sprayer for interior latex paint to paint bannisters. Worked beautifully. No dilution necessary. Make sure you warm paint to room temperature for a few days, strain the paint with mesh before putting it in reservoir, and use the larger aperture nozzle (included). Also dial up the air feed and paint feed to highest flow rates.
+10points
11out of 12found this answer helpful.
Was this helpful?helpful11unhelpful1

Asked by
Seattle
Read all my Q&A
December 23, 2014
Answer: 
These are gravity-feed spray guns, meaning you pour the paint into the gun's own container, through a strainer. So you don't connect the unit to the paint can/bucket in any way. It is NOT an airless or pump-type spray gun (like is often recommended for latex paints).
-2points
1out of 4found this answer helpful.
Was this helpful?helpful1unhelpful3

Asked by
Mukwonago, WI
Read all my Q&A
December 10, 2014
Answer: 
I have only ever used Behr Marquee Outdoor paint with a little paint thinner added. I believe you can use any paint... just keep in mind that indoor paint is thicker than outdoor paint. So if the paint doesn't go through the nozzle, add some paint thinner to your paint and you should be good to go!
+3points
3out of 3found this answer helpful.
Was this helpful?helpful3unhelpful0

Asked by
Colorado
Read all my Q&A
September 23, 2014
Answer: 
I used this gun to spray oil based "Rustoleum" primer and paint on a restoration project of an Old aluminum boat. The directions state that it can be used with either water based or oil based paint. Very little thinning was required for this paint. I have not tried it with water based or latex paints but see no reason with a little experimenting with thinning that it should not work.
+3points
3out of 3found this answer helpful.
Was this helpful?helpful3unhelpful0

Asked by
Anonymous
Orange, Ca.
Home Improvement Profile: Other
February 3, 2014
Answer: 
Hi Mrshirn, unfortunately these paint guns are designed to be used with stains, clear coat and enamel paints, such as automotive paint.
I would either rent a sprayer or use paint rollers.
-6points
2out of 10found this answer helpful.
Was this helpful?helpful2unhelpful8
 
5 answers

what tip size does these guns come in?

This question is from HVLP and Standard Gravity Feed Spray Gun Kit
Asked by
Dalton Georgia
Read all my Q&A
November 22, 2013
I want to buy this kit but I need to know the tip size they come in
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (5)

Asked by
LaGrange
Read all my Q&A
Home Improvement Profile: Professional
October 26, 2015
Answer: 
10/26/15 UPDATE to Painter: Thanks for your feedback. I called the number you gave to get the three 1.8mm parts and was referred to another number (800) 356-3392. The three parts come in a kit and my costs were $9.80 for parts and $5.95 for shipping.
+5points
5out of 5found this answer helpful.
Was this helpful?helpful5unhelpful0

Asked by
Flagstaff, az.
Read all my Q&A
Home Improvement Profile: DIYer
March 30, 2015
Answer: 
According to the specs., it should come with 1.8mm & 1.4mm tips. I haven't purchased yet but want more info. on painting a restoration.
+5points
5out of 5found this answer helpful.
Was this helpful?helpful5unhelpful0

March 3, 2015
Answer: 
1.4 MM on both guns
+4points
5out of 6found this answer helpful.
Was this helpful?helpful5unhelpful1

Asked by
Read all my Q&A
February 20, 2015
Answer: 
1.4mm and 1.4mm HVLP to get 1.8mm nozzle, cap, and needle you have to call husky tools 1-888-43-HUSKY part numbers are here http://www.homedepot.com/catalog/pdfImages/dc/dc2849fb-843b-49d1-8f3b-89c9f17a26cd.pdf
+11points
12out of 13found this answer helpful.
Was this helpful?helpful12unhelpful1

Asked by
Read all my Q&A
January 4, 2014
Answer: 
3/8
-6points
3out of 12found this answer helpful.
Was this helpful?helpful3unhelpful9
 
4 answers

Can I use these guns on a Harbor Freight 2.5hp 21 gal. compressor to paint a car?

This question is from HVLP and Standard Gravity Feed Spray Gun Kit
Asked by
Sacramento,Ca
Read all my Q&A
January 19, 2015
My HF compressor says that it's rated at 5.8cfm @40psi. The specs. on these guns say it only needs 4cfm@40 to operate. Is this true? Then shouldn't these guns be LVLP? Anyways, I was going to purchase the Spray-it 33000 LVLP, but after reading the excellent reviews & checking the specs on these guns, I'm leaning towards these HVLP guns. I just need some confirmation from anyone that paints cars regularly or someone that has painted a car with a similar set-up if this can be done with good atomization. Thanks.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (4)

Asked by
Louisiana
Read all my Q&A
Home Improvement Profile: DIYer
June 29, 2015
Answer: 
Mine is a 26 gallon from harbor freight and it works fine with these guns but I painted my car in pieces so I don't know about an entire car
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

March 3, 2015
Answer: 
Almost all professional auto shops use the HVLP technology. This is High Volume Low Pressure . This means that the gun operates on lower air pressure (Usually 20 to 30 psi). This allows for less bounce back on the paint or more paint sticking to the work surface rather than dissipating into the air.
+2points
3out of 4found this answer helpful.
Was this helpful?helpful3unhelpful1

Asked by
Read all my Q&A
February 20, 2015
Answer: 
If you are talking about the 21 gal. 2-1/2 HP 125 PSI Cast Iron Vertical Air Compressor
SKU 67847 then yes. CFM @ 5.8 @ 40 psi is plenty. I would use in line oil/water filter and make sure it remains above the compressor air hookup. I put it at the bottom of the spray gun.
+5points
5out of 5found this answer helpful.
Was this helpful?helpful5unhelpful0

Asked by
Atlanta, GA
Read all my Q&A
Home Improvement Profile: Professional
January 27, 2015
Answer: 
Hi ProjectC10,
I'm Travis from The Home Depot. Thanks for visiting our site.
Yes, you are correct that these Husky Spray Guns will operate optimally with the 5.8cfm(@40psi) of air flow supplied by your compressor.
These spray guns give you full adjustability of the mixing rate of the air and paint along with a gravity feed design to deliver the great results that you are expecting.
The kit is Read More
Hi ProjectC10,
I'm Travis from The Home Depot. Thanks for visiting our site.
Yes, you are correct that these Husky Spray Guns will operate optimally with the 5.8cfm(@40psi) of air flow supplied by your compressor.
These spray guns give you full adjustability of the mixing rate of the air and paint along with a gravity feed design to deliver the great results that you are expecting.
The kit is complete with in-line regulators, extra spray cups and paint filters. There's even a cleaning brush kit.
Thank you for asking,
-Travis Read Less
+8points
8out of 8found this answer helpful.
Was this helpful?helpful8unhelpful0
 
3 answers

Can this kit be used to spray texture on drywall?

This question is from HVLP and Standard Gravity Feed Spray Gun Kit
Asked by
Read all my Q&A
June 6, 2016
I purchased the kit and was wondering if I can use any of the guns provided to spray drywall texture (orangepeel) on my interior walls... Ya? or should I purchase something else?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (3)

Asked by
LaGrange
Read all my Q&A
Home Improvement Profile: Professional
June 7, 2016
Answer: 
No. You have to buy an appropriate hopper to shoot textures.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

June 7, 2016
Answer: 
This is not the proper gun for spraying orange peel. These are fine finish sprayers for cabinets, doors, shutters and automobile painting. They provide a smooth, fine professional finish. You need a hopper style gun for textured paints/materials. The model H4860HSG is ideal and is only available on THD.com. It will ship next day so turn around time is very fast. It not available in the store..
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Denver, CO
Read all my Q&A
Home Improvement Profile: Professional
June 6, 2016
Answer: 
No. Tip orifice is far too small.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
2 3 »
  • 2016-06-26 T16:09:08.016-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_203497812, prod, sort_default
2 3 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 208ms
  • QUESTIONS, PRODUCT

CUSTOMER REVIEWS

Rated 4.6 out of 5 by 42 reviewers.
Rated 4.0 out of 5.0 by Great product not a good customer service excellent Gun, works well with latex, you just need to dilute it by 15% with windshield washer liquid according to Youtube. worked well for me and I am not an expert. the package have 2 separate gun handle each have 1.4 mm nozzle, when I called them and ask for 1.8 mm as other reviewers says it was missing. They told me that gun comes with 2 1.4 mm, one is HVLP and other is not. and they wanted to charge me $17.00 for 1.8 mm tip which is just a metal piece. whole gun is sold for $30 on HD. anyway, some were able to get it and now they dont provide the tip and you are stuck with two gun regular and one is HVLP with same size nozzle. That is ludicrous. May 27, 2016
Rated 5.0 out of 5.0 by Great for deck project I dreaded painting the rails for the deck this spring. My neighbor suggested I get a spray gun. I thought that I would use a lot of paint with a spray gun. It was just the opposite. I sprayed the rails and my daughter followed up with brushing and we were done in 1/3 the time and it looks great. I am now looking forward to use my spray gun on my next project. June 23, 2016
Rated 5.0 out of 5.0 by Good product I did not have any experience with these types of sprayers but have been very pleased with my initial uses. It is important to follow the directions with regards to adjusting the spray pattern and flow. I also had a very good source of air, which I think really helped. The product itself is composed of very quality materials and I have been very happy with my purchase. December 18, 2015
Rated 4.0 out of 5.0 by E Z Painter light weight ready to paint . All a DIY needs to paint ! June 6, 2016
Rated 4.0 out of 5.0 by I Purchased The HVLP and Standard Gravity Feed Spray Gun Kit from local HD. I inspected all components and noticed the PN 9B9802-18,9B9803B1-18,9H9809C Air cap, nozzle,needle 1.8mm are not included. I called the husky customer service and they spoke with the warehouse they are shipping out the parts. The call took about 5 min great service. The larger size will help with thicker material like marine varnish. February 20, 2015
Rated 5.0 out of 5.0 by Good for the price I have only used the HVLP gun in the kit so far. These are NOT technically HVLP as they require 20 to 40 psi to operate. True HVLP runs on 10 psi or less. Be that as it may, this spray gun works well and puts out a nice fan. I used it to paint a very small part approximately an 8" cube. It atomized the paint sufficiently and did a nice even job. I am spraying Sherwin Williams Polane catalyzed paint. Clean up was easy and the small cup that I used came 99.9% clean with very little solvent. The best part of this gun is that you can spray virtually 100% of the paint in the cup. There is no waste or need to mix a little extra. This is far better than siphon style guns. I have an Accuspray $400 true HVLP (5psi) gun and this new gun will be replacing it as it lets me get closer to the parts on a table because there is no can hanging under the gun, as well as its efficiency and ease of cleanup. One other thing that is needed is a stand for the gun. There is no easy way to add paint to the gun and put it down between jobs. I made my own from some wood and it works perfectly. Pictures included. February 17, 2015
Rated 4.0 out of 5.0 by Latex needed thinning or larger, 1.8mm aperture nozzle (optional through Husky Parts Dept) I bought these guns to spray latex Glidden Gripper primer and latex satin enamel on kitchen cabinets. I filtered the primer through fine mesh cone filters before filling the gun cup and used the gun filter which was included in the kit. The gun would not spray the primer until thinned by about 20%-25%. I called the Husky parts line at 1-800-654-0688 and ordered the 1.8mm tip and needle for both guns in the kit. Cost was about $16 each with shipping for a total of roughly $32. I have not yet received the larger aperture tips but I suspect the additional .4mm will make all the difference in the world when trying to spray thicker latex finishes. The gun did an excellent job spraying the thinned primer and left a smooth as glass finish but i'd prefer not to dilute by 25% for obvious reasons. The knobs for the fluid control, fan size control and air control are all plastic so be careful not to cross-thread! As much use as these knobs will get they should be metal and therefore 4 stars for my review instead of 5. January 4, 2016
Rated 5.0 out of 5.0 by Outstanding for interior Latex paint I rarely write reviews for products but I went out of my way to come back to the website and write about this gravity sprayer. I bought it five months ago and I have been working this tool HARD. I first used it to spray interior bannisters and hand rail on stairs (big project, mostly for all the masking work), later to do kitchen cabinets/doors/drawers and more recently to stain exterior adirondack chairs. There is a lot of ambiguity about using latex paint in HVLP sprayers but let me be clear that this sprayer laid down latex paint beautifully without clumps, chunks or drips (no I did not dilute the latex paint in any way). A few key recommendations for using latex paint in this sprayer: use the larger aperture nozzle (included), warm paint to room temperature for several days beforehand and use mesh straining cloth to strain out any chunks as you pour paint into the sprayer reservoir (mesh straining cloth available in any paint department). I ran it with the adjustable air input and paint input settings dialed as high as possible with compressor at the recommended 40PSI. When you are ready to spray, spend a few minutes dialing in settings while spraying on test material. Cleaning the tool takes 10 minutes once you get the hang of it. Really pleased with this tool. High quality and it comes with extra parts which is a plus. This is my first Husky product and I would definitely consider their other products in the future based upon this experience (see attached before and after shots of bannister). February 15, 2015
  • 2016-06-26 T16:52:10.081-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_42, tr_42
  • loc_en_US, sid_203497812, prod, sort_default
2 3 >>
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 118ms
  • REVIEWS, PRODUCT