Rated 4.5 out of 5 by 29
Rated 4.0 out of 5.0 by Villa Husky tube cutter
Good product I willrecommend to buy make on you for your project
May 25, 2016
Rated 5.0 out of 5.0 by EricG Makes clean cuts every time
I have a small tubing cutter and I like how it makes a clean cut, but the capacity is only about one inch. In the past I have used my power hacksaw to cut larger diameter tubing. It does make a square cut, but the edge of the tube is left rough on the inside and outside so I have to clean it up with a file and reamer.
This cutter does an excellent job of cutting tubing. The cut is square and the only imperfection is a burr on the inside, but this cutter includes a reamer which makes quick work of cleaning the cut.
Recently I made a router compass to cut the ribs for an observatory dome. I needed to cut diameters up to 15 feet, so I made a set of different length tubes for the different curve radii, and this cutter did the job in minutes.
December 2, 2015
Rated 5.0 out of 5.0 by Mamajane1234 Cuts with ease
I like this tube cutter. The design is heavy duty with a nice screw handle. It cuts a 2 ⅛” pipe with ease. Cutter blade works well. It is easy to hold and turn around the pipe. I am also successful holding the cutter and turning the pipe. The red quick release button and the pop out metal reamer blade add a level of convenience. The quick release allows you to immediately slide the hold assembly portion of the cutter away from the pipe being cut. Also rather than having to screw the hold assembly all the way in, you can slide it along the track until snug, then tighten with screw assembly. The reamer enables you to smooth the inside of the pipe to dull sharp spots and remove burrs.
October 3, 2015
Rated 5.0 out of 5.0 by WestSkyGuy Easy to use, left a clean cut
Purchased this item to cut away old aluminum piping that had to be replaced. The piping ranged from a diameter of 1.25" to just under 2". The tool cut the piping with a minimum of effort, leaving clean cuts and only needed a minor amount of filing down. Very happy with the tool. Don't have a huge need for pipe cutting, normally, but this will stay in the tool box for whenever I need it again.
April 17, 2016
Rated 5.0 out of 5.0 by frljo1 one the best that i operate with
this is the one off the best pipe cutter that i worked with i cut M type (commercial) copper pipe without big effort whatsoever.
the quick release/adjust is just a bonus on the tool I'm a maintenance guy dealing with everything if this cutter wore before on the shelf I would buy it in a heartbeat.
in the handle there is extra cutting while also a bonus, if you are a plumber or electrician do not hesitate it will speed up your installation for more than 30%
September 22, 2015
Rated 4.0 out of 5.0 by Frankieg Heavy Duty
The Quick release tube cutter does well from 2 inch down to 1/2 cooper tube. It makes a nice clean square cut. I didn't notice any walking cutting several diameter pipe. Cutting larger pipe it's a little harder to cut short pieces from short stock as holding the pipe is harder . Using a clamp,or vise it works great. Making the cuts Worked out nice, the deburring blade works but not great it need more cleaning with a hand deburring tool or sand paper. The outside of the cut is clean so slipping into unions is nice with little cleaning. The quick release works but can get temperamental if you don't position your finger correctly you also need to be sure you don't have any pressure on the pressure knob or it won't release while pushing to the pipe. For clamping down on the pipe the quick release is fast, just push on the knob. On the pipes I tried 1/2 3/4 1 1/4 and 1 3/4 clamping down with the quick method gets you close to the pipe but not enough to be able to release the pipe and twist the knob to make cutting contact. A little fumbling but no big deal . All in all a good tool for large and small pipe, good price point . It's built sturdy , good feel and a little on the heave side.
September 18, 2015
Rated 4.0 out of 5.0 by Jason31 Good tubing cutter for commercial plumbing
This is a great cutter, the quick release makes it very easy to use. This is best for commercial plumbing where you need to cut larger copper for drains as well as the smaller 1/2" to 3/4" tubing. I say this because it's a little big if all you need to do it cut 1/2". Works great on the large pipe and small pipe.
The quick release works well, but when tightening, the jaws can be pushed closed, but not far enough to grip the pipe, you need to turn the knob to get the jaws to close.
The spare cutting wheel in the handle is a good addition, however the cover popped off after the first use. I tossed it, since it really serves no purpose.
October 30, 2015
Rated 1.0 out of 5.0 by JasonL Mistracks on smooth round curtail rods - probably okay on copper
We attempted to use this to cut through smooth round curtain rods. Our old pipe cutter did a great job except the rotating bearing wheels were rusty and marred the curtain rod. Despite the cosmetic issue, the old pipe cutter made clean cuts and did not wander during the whole cut. So to avoid the rust marring the curtain rod,we bought this new Husky 2-1/8 inch tube cutter from HD as it looked very similar to our old USA built unit, but the Chinese Husky mis-tracked, meaning the cut would wander almost 1/8 inch as the tube was rotated. This made it useless for making nice cuts so after several attempts we gave up and will return it. That said, if the goal is just to cut copper pipe and wander is not critical, then the Husky is probably okay.
December 16, 2015