Rated 4.5 out of 5 by 36
Rated 5.0 out of 5.0 by Randy Cuts Better than Expected
The Quick Release 2-1/8 in. Tube Cutter cuts a variety of different types of tubing with the greatest of ease. I don't cut a lot of tubing so I have been using a mini hacksaw to do the job. The saw did not make a very clean or straight cut. When I received this Tube Cutter I was very excited to see how it would cut the spare tubing and pipe I had available. It cut a 1 1/8" pvc and1/2" cpvc pipe in seconds. Next I cut a 5/8" plastic electrical conduit just as quickly. I was really amazed when I cut a 3/4" galvanized pipe with very little more effort than it had taken to cut the plastic tubing. I love this Tube cutter. It cuts up to 2 1/8". I recommend this product.
August 24, 2016
Rated 5.0 out of 5.0 by HCHomeowner Very good quality tube cutter and reamer.
This is one hefty tube cutter and it works like a fine quality C clamp with a quick clamp release feature. I used the knob to adjust to a steel electric conduit, quickly cut through it, and used the knob to adjust it back. I then repeated using the quick release (small red knob) to adjust to the electric conduit, cut it again, and used the quick release to remove the conduit. This is one smooth tool. There is a slide out reamer in the cutter body and an extra blade in the knob. My only gripe is there are no directions with this tool but it's so good I'm rating it five stars.
August 21, 2016
Rated 5.0 out of 5.0 by oddroc I'm impressed!
I bought this to do some chain link fence work without having to resort to a hack saw or sawzall to mangle the posts and rails. I just used this on some 17 gauge top rail, and it worked as well as any good-quality smaller tubing cutter on copper pipe. I especially like the width of the support rollers. I was worried that this cutter might spiral down the tubing, but it worked like a champ and made quick work of the task.
Next task - 16 gauge line post!
July 30, 2016
Rated 1.0 out of 5.0 by Hhjkg Works when it stays together
If youplan on using it alot locktite every screw on the thing or they will all fall out. Or buy a ridgid
August 22, 2016
Rated 5.0 out of 5.0 by Garageman Perfect for the job
Bought this to get a clean cut on heavy duty closet rods and I was concerned it might not be up to the job. As soon as I started, it was obvious that this was a good tubing cutter. Just needs a little patience and it works like a champ.
July 19, 2016
Rated 5.0 out of 5.0 by thebutlerdidit It worked
A bear had pushed over my feeder pole which was galvanized with a diameter of 1 and 1/4 or 1 and 3/8 inches. It was in concrete that was underground so, rather than try to dig out the whole thing, I cut it off below grade with this. It worked even though the pole had a bit of a bend in it. My 'back' says this was 20 bucks well spent even if I never use it again.
June 19, 2016
Rated 5.0 out of 5.0 by keith Works great
I used it to cut 5/8 inch aluminum tube and 1 inch plastic pipe. Not fast but gives a clean square cut.
August 2, 2016
Rated 5.0 out of 5.0 by Mamajane1234 Cuts with ease
I like this tube cutter. The design is heavy duty with a nice screw handle. It cuts a 2 ⅛” pipe with ease. Cutter blade works well. It is easy to hold and turn around the pipe. I am also successful holding the cutter and turning the pipe. The red quick release button and the pop out metal reamer blade add a level of convenience. The quick release allows you to immediately slide the hold assembly portion of the cutter away from the pipe being cut. Also rather than having to screw the hold assembly all the way in, you can slide it along the track until snug, then tighten with screw assembly. The reamer enables you to smooth the inside of the pipe to dull sharp spots and remove burrs.
October 3, 2015