Model # HKS3198NFL

Internet #203856701

Kingston Brass Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
0663370289453

Kingston Brass

Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems

$55.70 /box

Frequently Bought Together

Product Overview

Replacement Filtration Faucet in Satin Nickel will complement any kitchen decor. The tall spout has a high-arc that is ideal for pouring drinking water. Works with most under-counter drinking water systems.

  • Easy to install
  • Single-handle deck mount
  • Ceramic disk cartridge
  • Fabricated in solid brass for durability and reliance
  • Can be used for reverse osmosis with the addition of an air gap (air gap not included)
  • Filter faucet uses 1 hole, additional holes are required depending on kitchen faucet
  • 90° swiveling spout
  • Quarter-turn on/off water control mechanism
  • All mounting hardware included
  • For cold water only

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

5 Questions6 Answers

Customer Questions & Answers

Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
2 answers

What size hole is needed to mount the faucet to counter top?

This question is from Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
Asked by
Read all my Q&A
June 8, 2015
I checked the listed specifications and it is not shown!
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (2)

Asked by
CA
Read all my Q&A
Home Improvement Profile: Professional
November 5, 2015
Answer: 
The hole size needs to be large enough for the 1/4-inch supply line, but small enough that the faucet covers it (faucet is 1-3/4 inches). It is recommended to be around 1/2 inch.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

June 9, 2015
Answer: 
Inlet is 1/4 inch. The faucet measures 1-3/4 inches at the base. It is recommended to use a hole between 1/2 to 1 inch.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
1 answer

What is the differance between the HKS3198NFL and HKS3198FL?

This question is from Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
Asked by
Read all my Q&A
September 18, 2016
It is a replacement for a NON R.O. system that uses a carbon block filter.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answer (1)

September 19, 2016
Answer: 
They are the same with a slightly different handle style.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
1 answer

Is there a filter that can remove salt from the water that is in the water from using a water softner?

This question is from Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
Asked by
Read all my Q&A
September 7, 2016
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answer (1)

September 8, 2016
Answer: 
This is just a faucet. Please discuss filtration options with your local Home Depot store associate.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
1 answer

What kind of air gap do I need to buy?

This question is from Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems
Asked by
Rochester, NY
Read all my Q&A
May 6, 2016
I looked up "air gap" and there are many different kinds. What kind do I need for this faucet to use with my reverse osmosis system?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answer (1)

Home Improvement Profile: Professional
May 12, 2016
Answer: 
Any air gap should work. You may want to consult with your local Home Depot store plumbing associate about your application.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
2 »
  • 2016-10-30 T23:52:21.844-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_203856701, prod, sort_default
2 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 88ms
  • QUESTIONS, PRODUCT

Customer Reviews

Replacement Drinking Water Filtration Faucet in Satin Nickel for Filtration Systems is rated 4.4 out of 5 by 10.
Rated 4 out of 5 by from Works well and is well made. Works well and is well made.
Date published: 2016-12-20
Rated 2 out of 5 by from Can't seal, poor design, lousy installation. We have had an older faucet that we had been using for years with our RO system. Since we recently purchased a very nice new water faucet, we wanted a nice RO faucet to match. After some looking around, I settled on this faucet .. it looked nice in the pictures and got good reviews. Well, we also have a very nice and expensive older Elkay stainless steel extra deep kitchen sink. The old RO faucet was mounted there and the new faucet was going in the same location. At least that was the plan. Turns out that they didn't really think things through when designing this faucet. There's an o-ring on the bottom of the valve body that would seal and work well if you have a very small hole (like in stone) and are not using the included decorative metal flange .. that's where the design planning stopped on their part. 1) There is absolutely NO WAY to seal between the faucet body and the decorative flange .. nada. And the decorative flange has a groove where the valve body sits that is just slightly larger in diameter than the valve body, leaving a really convenient place for water and stuff to collect. 2) The bottom of the flange has an o-ring to seal to the sink surface, but only if your hole is 1.25" or smaller. With my sink's holes being 1.5", the o-ring was 100% useless. 3) The too thin plastic washer they use underneath to hold the faucet in place is exactly 1.5" in diameter, which just so happens to be the exact size of all the pre-drilled holes in my sink, thus making it impossible to mount the faucet. Fortunately, the decorative flange is just slightly larger than 1.5" in diameter, so centered it just fit on top, but it wouldn't seal. So, I had to reuse the very thick (more than twice as thick as the whimpy plastic washer they supplied) and properly sized plastic washer from my original RO faucet to hold this new RO faucet in place. As it was completely impossible to seal this faucet between the decorative flange and the faucet body, as well as the o-ring being too small in diameter to fit the size of my predrilled sink holes, I decided to fill the entire cavity between the faucet, decorative flange and the old thick plastic washer with plumbers putty. I place a large amount in the void area and just cleaned up all the squished out putty after tightening the faucet in place. So the faucet looks nice and seems to work well. But unless you have a drilled hole through stone, this may be a nightmare to install. Had I known about the issues before hand, I would have never purchased this faucet. So all that in hand, I tried to contact the company to complain. No one I spoke to was willing to talk to me about it. The only person that could help was their "buyer" and he was "away" and they weren't sure when he would be available. 100% useless customer service. So the quality is okay, the sealing design only works for one type of install, the install was all but impossible without using parts they didn't supply, and their customer service was useless. Thus, this is getting a 2 stars.
Date published: 2014-04-23
Rated 5 out of 5 by from Attractive, sturdy, functional Well made and a smart purchase....................
Date published: 2015-12-10
Rated 5 out of 5 by from Love this purchase! I previously had a very inexpensive and small spigot for under sink filter. This is so much nicer and looks beautiful next to my brushed nickel faucet.
Date published: 2015-04-21
Rated 4 out of 5 by from Good Faucet - small install issue The only reason I didn't give this a 5 star is because the backer plate that holds the faucet to the sink is made of plastic. If you have a larger hole in which to mount you faucet it is impossible to tighten the nut enough to keep the faucet from swiveling. Otherwise it seems pretty good out of the box.
Date published: 2014-11-28
Rated 5 out of 5 by from As good as expected The product was great and easy to install for an all thumbs guy like me. the actual purchase at the store -- this was an online-store pickup -- was the most difficult part of the whole project.
Date published: 2014-09-25
Rated 5 out of 5 by from Replacement reverse osmosis faucet We upgraded to granite in our kitchen and needed a new faucet. The brass one from Home Depot was perfect and matched our stainless steal appliances very well.
Date published: 2014-12-23
Rated 4 out of 5 by from good product Hole on my sink is slightly bigger, I thought this fits standard hole but I had to find a washer to user under the hole to be able to install it.
Date published: 2014-12-23
  • y_2017, m_1, d_20, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_, sid_203856701, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 73ms
  • REVIEWS, PRODUCT