Rated 4.5 out of 5 by 25
Rated 4.0 out of 5.0 by rsmaudsley Good sliders, bad screws
I originally thought that the person who said the screws were bad just didn't know what he was doing. In my case the screws didn't break, but the heads stripped out very easily. The only screws I "lost" were the ones that went in to the desk. The ones for the keyboard tray did ok.
Fortunately I had some self-drilling #10 screws that I used to secure the sliders to the desk.
I'm giving it 4 stars because it was easy to mount and I like the sliders themselves seem to be of good quality. So as a previous posted stated, buy some good #8 3/4" or 1" screws and use them.
Remember to make sure whatever screws you do get are not longer than the depths of your desk top or keyboard tray.
May 20, 2011
Rated 2.0 out of 5.0 by clementine If you buy this, buy replacement screws too
We installed the D807 Series Keyboard Slide into a hardwood desktop; we pre-tapped the holes. While turning the screws (hand turning with a screwdriver, not a drill), several screws snapped. So we had to re-measure and tap new holes, and the tray is no longer in the perfect position...overall disappointing and it added more time for a "quick" project.
The screws are too soft, so don't waste your time with them as we did. We still went ahead with installing this, hopefully the rest of the materials aren't as cheap as the screws.
For replacement screws, you'll need 14 #8 x 5/8 pan head wood screws.
May 12, 2010
Rated 4.0 out of 5.0 by BFVSFOREVER Don't understand the problem with the screws
I almost purchased a set of slides for my new keyboard drawer from Rockler for almost twice the price because of the previous review. The original slides had broken after years of use. I made a new drawer out of Maple. I rethought it and decided to go with the Home Depot slides, Very nice slides, they roll smoothly and lock in place when retracted. The screws went in with no problem, just make sure you drill the right size pilot hole! Just like a square peg you can't drive a screw into a round hole if its not the right size. A very good product, I would buy it again with no reservations.
September 11, 2010
Rated 5.0 out of 5.0 by Brittany perfect!
Fulfills exactly what I wanted. I built a desk inside my closet and this was the perfect finishing touch. I had originally planned on buying an entire keyboard tray, but instead I picked up a 16 in. piece of wood and painted it to match the rest of my desk and shelves. Most people said they had problems with the screws..I've been there, although I did not have a problem with these. Just be gentle with them. No need for extra power.
Smooth gliding, easy install, no sharp edges!
September 30, 2011
Rated 4.0 out of 5.0 by caqmd replacement
I bought it to replace an older one (installed about 10 years ago) which broke. It is a little tricky to attach it and properly align it to the underside of the desk surface but works well once installed.For the shelf itself (not included) I used a prefabricated laminate 3/4" shelf (16" deep X 24" wide)
May 3, 2013
Rated 5.0 out of 5.0 by Consumer101 Very well built
If anyone is looking for a very good quality sliders at a low price, this is perhaps it. Had to change the keyboard sliders/rails for our computer cart, for which the keyboard kept sliding in and wasn't locking in place. The installation took about 1.5 hrs. If you still want to save, just run to a near by home depot and pick it up (costs $10!)
December 5, 2011
Rated 5.0 out of 5.0 by Jarrod Great Value for the price
I am very happy with the keyboard drawer slide. I have been using it for several months now and have been pleased with its ease of operation.
March 24, 2014
Rated 5.0 out of 5.0 by Alan Excellent Product
The under counter keyboard tray hardware was perfect. Installation was a piece of cake. We are not using the tray for a keyboard but using it to stow away a remote hard drive, phone charger, blue tooth charger, calculator and other stuff that was making the desktop messy. These are necessary items to have at hand, but not accessible all of the time.
October 9, 2012