Rated 4.5 out of 5Â by 14
Rated 5 out of 5Â by JoeSeattle Finally, an easy way to fix chipped tile.
Works as advertised. took 60 seconds to knead and then I had about 3 minutes to work it before it got hard. Try slicing off the amount you think you will need to prevent waste. I think it would would work well in the suggested uses. Just be sure the area is brushed clean of any debris that may prevent adhesion.
Each piece is sealed so it is good to keep on hand. It dried to an off white. A bit whiter than builders beige.
The first chip I repaired was a nickel size hole in the entryway tile. See attached photo. Unless you are looking for it it goes unnoticed. The base of the tile is dark brown so the chip was very noticeable. I used several markers and smeared them to blend to the approximate color and add a little speckling to match the tiles as best I could. Water color may have worked a little better to get the right color but not sure the color would last. I was very pleased with the results.
the 2nd chip was in our shower and the base of the tile was white so it blended in just fine without needing to color it. Just push it in wait for it to dry and clean up the edges with a knife like you would with grout.
I will definitely be buying this for future repairs.
July 2, 2014
Rated 5 out of 5Â by DIYer88 Great product!
I tried this product to repair some damage to a ceramic tile that occurred after dropping a can on the floor. The damage was roughly one inch in diameter and I needed something that was very strong and durable, since the other option was cutting out that tile to replace it, so I decided to give this a try. The package has two pieces of putty, each approximately 3/4" long, 1/2" diameter. Since the damage to the tile was small, I decided to cut one of the pieces in half, which ended up being plenty for the small hole. The directions say to knead the putty for one minute and it would be workable (pliable) for about three minutes. I kneaded it for a minute and pressed it firmly in to the hole using a putty knife for added pressure and worked it in. (The putty actually began to cure and harden before three minutes so you'll need to work fast.) I let it cure overnight and sanded it the next day. The material seems pretty hard and although not the same as ceramic tile, it looks like it will work for the repair. One other note is that the instructions say the material dries white, but it was an off-white (which actually worked better for my project).
June 16, 2014
Rated 4 out of 5Â by Yellowjacket Great Product, But Work Fast
How many times do you get a tube of wood filler or putty, only to have it harden up in the tube before you use even half of it? This product comes in a blister pack with two single-use size capsules. You can use one without having to expose the other to the air.
The product seals well, is relatively easy to work, and almost odor-free. It sets up quickly.
But, work fast. From the time you open the package until you finish, you have roughly 4 minutes: 1 to knead the components together, and 3 to work the putty before it becomes too stiff.
July 10, 2014
Rated 5 out of 5Â by fizzie Strong and easy to apply
I've use other types of these 2 part putty's and at best its a guess if I have the mixture ratios correct. With this one there is no guessing just mix as the directions say and apply to a clean surface. I used it on plastic electrical conduit pipe connection that came apart, first I roughted up and cleaned the surfaces with a 300 grit sandpaper and then applied the putty. Worked great and I made a nice clean edge with an exacto knife before it dried completely.
July 24, 2014
Rated 5 out of 5Â by Desertheat1 Excellent Product
I applied this putty to a broken plastic part on a kids wagon by the wheel. I know on the package it said you could drill it,because of the strength after it hardened, but I can tell you I was VERY IMPRESSED WITH IT'S STRENGTH when it dried. It went on very smooth, and was also easy to paint after it hardened. I can see this product being VERY useful, and I will definitely try it on other projects!
June 17, 2014