Rated 4.1 out of 5 by 8
Rated 5.0 out of 5.0 by Francisco Best roofing gun out there
I worked with a lot of roofing guns and by far the Makita 1 3/4coil nailer has to be number 1 and I been roofing for 15 years really light weight and reliable tool.
October 18, 2016
Rated 4.0 out of 5.0 by JKG Nice product
Use to do an entire roof, Easy to load, shoots straight and true. Jammed a couple of times but I think it was the cheap nail I was using. Be sure to check all of the allen screws before you use. Some of them loosened right away. One fell out completely before I noticed.
September 13, 2016
Rated 5.0 out of 5.0 by Joe Works Well
Used this to put a roof on my large 16 x 12 shed. Went over the old shingles with no issues using 1 3/4 nails. Air at 110 psi with a 25 ft. hose. A little expensive but it feels and works like a quality tool.
June 6, 2016
Rated 3.0 out of 5.0 by Cloe Good for occassional use
Will work for the DIY as it's not commercial quality. Too many misfires (double nailing) and does not sink the nail flush even though the depth & p.s.i. it set correctly. The metal casting is irregular showing this was not made with quality in mind. When doing a complete roof would not recommend. But for patch or repair yes, as it's easier than hammering roofing nails with bare hands!
June 26, 2015
Rated 5.0 out of 5.0 by Steve Nice and light
It arrived quickly and was well packed. Mine came from the factory in a box within a box within a box. Included accessories are safety glasses, lubricating oil and an air hose quick disconnect already installed.
The gun ships fully assembled and ready to load and connect to a compressor supplying dry, filtered air at 65-120 psi. The nail magazine holds a coil of 120 nails from 3/4" to 1-3/4". Like all other pneumatic tools this one requires a constant source of lubrication from an inline oiler or manual daily lubrication before and after using the tool. Two or three drops of the supplied oil through the air inlet will do the trick. The nails load easily and there's a small magnet that ensures the last nail in the coil feeds reliably. This gun features a belt clip, an adjustable shingle guide and a tool-less depth adjustment. The depth adjuster is a knurled knob that when turned clockwise increases the driven depth and counter clockwise to decrease. You can add additional adjustment by increasing or decreasing your compressor pressure.
Like my other roofing nailers this one can be single-fired by pressing down on the work piece and pulling the trigger or bump-fired by holding the trigger back and bumping the nose piece against the work. I normally run my compressor at 90 psi and at that pressure I was able to fine tune the nail depth with the built-in adjuster.
My other guns don't have a shingle guide and I don't foresee me using this one. I was taught to snap chalk lines and I find that method fast and accurate. I drove a half coil of one inch nails into a shingle over 3/4 inch plywood backing with no problems. To truly test its functionality I'll have to test it on my next roofing project which should happen in the fall.
By the way, I've found these nailers are useful for other projects besides roofing. I've used mine to install sheathing, new construction flanged windows and wallboard on ceilings. It's a very fast way to get a couple of nails into heavy ceiling boards proir to finishing the job with sheetrock screws.
Makita offers a 30 day refund or exchange and a 3 year warranty when a defective tool is returned to an authorized service center.
June 27, 2015
Rated 5.0 out of 5.0 by markerz easy
glad makita made this coil nailer...goes great with my other makita tools
February 22, 2016
Rated 1.0 out of 5.0 by daj541 Terrible replacement for the AN451
I purchased one of these to augment my AN451 and found it could not sink nails while rapid firing. You had to hold the gun down on each nail and then hit the trigger to get them to sink most of the time. I returned it and got another new AN453 as a replacement and it functioned the same. Makita changed the internal design on this gun and it will not sink the nails. I bought a used AN451 and it works perfectly. This is really a shame as I own thousands of dollars in Makita tools and all but this new roofing nailer work great.
September 23, 2013
Rated 5.0 out of 5.0 by jf3men Great roofing Nailer!
Extremely well built and durable nailing gun, very high quality!
June 3, 2014