Model # 733307-A

Internet #205317490

Makita 1/4 in. Carbide-Tipped 2-Cutter Tongue and Grove Router Bit 2-Wing with 1/2 in. Shank


1/4 in. Carbide-Tipped 2-Cutter Tongue and Grove Router Bit 2-Wing with 1/2 in. Shank

$5368 /each

Frequently Bought Together

Product Overview

Makita Router Bits are designed to work with routers in a variety of routing applications. The bits feature high quality carbide for more efficient material removal. Each bit is manufactured from high quality steel for added durability and long life.

  • Carbide tipped for improved speed and long life
  • Ideal for making both tongue and groove cuts by reversing the assembly
  • Ball bearing pilot for improved accuracy and efficiency
  • For use with routers that accept 1/2 in. shank bits




More Products With These Features


Customer Questions & Answers

is it sold out of stores or only on line

is it sold out of stores or only on line
Asked by: sal
Hi Sal, this item is an online exclusive item and comes directly from the inventory where it can be shipped to you directly or if it is eligible, shipped to a Home Depot store. We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot!
Answered by: THDSupport
Date published: 2016-11-23

Are the instructions for assembling the groove cutter configuration wrong?

I attempted assembling the groove cutting bit as shown in the instructions with only one bearing below the cutter. I included all the shims shown, and left out the second bearing. The assembly didn't stack up far enough on the shaft for the nut to tighten down properly. I disassembled and installed the second bearing above the cutter, and everything seemed to fit. Is the second bearing supposed to be installed for this configuration, and the instructions are just wrong? Or am I missing something?
Asked by: Doresoom
Makita bits and routers are engineered for precision and performance. To confirm correct assembly, please contact our Call Center at (800)4-MAKITA. Makita Customer Service Representatives are based in Buford, Georgia, and ready to help.
Answered by: MakitaTeam
Date published: 2017-06-11
  • y_2017, m_6, d_23, h_10CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_, sid_205317490, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 95ms

Customer Reviews

1/4 in. Carbide-Tipped 2-Cutter Tongue and Grove Router Bit 2-Wing with 1/2 in. Shank is rated 5.0 out of 5 by 1.
Rated 5 out of 5 by from Airtight tongue and grooves! I tested this bit out on a scrap of 1x pine stock I had lying around my garage, and I was really impressed with the results. Using my 2-1/4 HP Bosch router, I chucked up the 1/2" shank into the collet and cut the tongue side first. I did it in two passes, since I was working with the handheld router, rather than on a table. The bearing did a great job of keeping the router sliding smoothly on the final pass. The cutting was very smooth, and I didn't experience any burning or tearout at all! Next, I swapped the cutter configuration out for the groove portion. I noticed that the diagram in the included directions must be wrong, since it only shows one bearing installed above the cutter. However, there aren't enough shims and spacers to get to the threaded portion of the bit shaft without including the second bearing. Anyway, I ignored the directions and installed the second bearing, and everything cinched up fine afterwards. The groove portion was even easier to make, since there's only one cutter. I did find out afterwards though that I didn't get the bit seated at quite the right height in the collet, and my tongue was offset from my groove about 1/16"-1/32". Looks like it's time to make a template! Putting the two edges together, you can see the resulting joint is nearly airtight! If it wasn't for the grain differences, I think it would be nearly impossible to tell it was there after gluing and clamping.
Date published: 2015-05-17
  • y_2017, m_6, d_22, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_, sid_205317490, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 96ms