Rated 3.4 out of 5 by 9
Rated 5.0 out of 5.0 by Bayotle Perfect except
Used these to redesign my closet.
One person complained (on here) the holes were not aligned properly, this should only be if you've flipped the board. One side the holes are (guess-ta-mate) 1.5" from the edge and 2" from the other edge - this means you can't just flip the board and expect the holes to be the same (though it shouldn't affect putting shelves on it)
My complaints if you can call them that are simple, having to drill through 150 holes so I could attach shelves to both sides and the holes not being the same distance from the sides - both minor and workable.
August 22, 2016
Rated 5.0 out of 5.0 by Darci Carpentry made easy!
I built the perfect media cabinets for my new house in 6 hours from planning to playing video with these boards! Two of these cut for sides, the undrilled ones for tops, bottoms, and shelves, wham - shelves just how I wanted them, at a much cheaper price!
February 17, 2015
Rated 1.0 out of 5.0 by Hck Stickers don't come off
This would be a great product except for the fact that the company puts huge (14"x6 1/2") stickers on each board that are nearly impossible to remove without damaging the finish. Time is money in my business and I don't have time to remove pointless stickers.
January 20, 2016
Rated 3.0 out of 5.0 by mike Think before you cut this board
If you only need a portion of the board think about two things.
1. There is only one white side (it would have made it so much easier if they put the white siding on both sides).
2. The peg holes have to line up.
So you'll need to consider cutting from both ends of the board to line up the peg holes and show the white siding.
This advice would have saved a bunch of time and money.
November 12, 2015
Rated 5.0 out of 5.0 by DrBob Useful and Easy to Use
Built a shelf unit between 2 cabinets for laundry room. Overbuilt using biscuits and glue, but holds 2 warehouse store (huge) detergent bottles and lots of other heavy items easily (put detergent on its side to make it easy to dispense). Big improvement, not a lot of work.
If you have the cut edges showing, buy some matching edge tape and borrow a clothes iron to seal it on the unsightly edge. Takes a few minutes, and looks very professional.
The label is no problem! Easiest way to remove it is by warming it with a heat gun or hair dryer to soften the adhesive, and gently peel it off. Or use Goo-Gone remover or equivalent and let it soak in to break the adhesive bond. you can lightly score the glossy surface of the label (DON'T cut through and scratch the work!) Give it time to wet through the label. You can also use Mineral Spirits from the paint department, or lighter fluid. These are great for removing gummy residue, also. Alcohol doesn't work; all it does is make you write angry reviews.
June 28, 2015
Rated 5.0 out of 5.0 by TheKid Built a pantry, this worked great
I built a pantry using this drilled board for uprights, so that the shelving would be adjustable. I had to drill out the holes to use the shelf pins on the backside of the middle upright board, but if you drill a smaller starter hole and then progress bit by bit to the correct size drill bit, you can get as clean a hole in the melamine as the original.(I'm too frugal to put two boards back to back.) The labels on the board, while Very Big, came off very easily, in one piece, with little gummy residue.
February 2, 2015
Rated 1.0 out of 5.0 by carpenter non-removable label!
Could they make the GD label any larger, more difficult to remove, and a bigger pain? I spent three minutes cutting the boards to size and twenty minutes removing the labels with my chisel...then I spent ten minutes tracking down the rubbing alcohol I needed to remove the leftover glue on the boards...then another few minutes wiping off the residue. Just the way I like a project to go!
January 7, 2015
Rated 4.0 out of 5.0 by Keithbrit Easy to build and organize a closet
I did a complete walk in closet using this product, it took a day and a half, although some of that was going back for more boards. Only complaint us that the boards are only drilled on one side, makes it necessary to put boards back to back. Having done that, the whole project Cost a little over $200. For this I was able to treble the hanging space and build 58 feet if shelf space.
December 28, 2012