Rated 3.5 out of 5 by 11
Rated 3.0 out of 5.0 by COdude Milwaukee portable band saw table
This product was difficult to adjust the angle for 90 deg. Once assembled at 90 deg angle (at best), it is best use for large pipes & tubes.
I bought this table since I had the Milwaukee portable saw already.
Better designed for plumbers & electricians.
Not designed for metal fabrication tool.
Really lame it does not have a vice for hold down or a vertical cut table.
The FEMI 782XL mitering band saw is more likely to serve me better and at a reasonable price.
October 25, 2016
Rated 4.0 out of 5.0 by Crusader well crafted
Once the saw is mounted it requires some fine adjustments to enable the blade to square to the clamp,
then tilt the blade to address the material within the clamp at a true 90 deg. from start to finish.
If not, it will cause the blade to not track properly.
April 26, 2016
Rated 4.0 out of 5.0 by steelcraftsman useful, reasonably simple to set up. a good tool.
the chain clamp holds securely but you need to fiddle to get it hooked each time. the lower travel stop is a socket head cap screw. it could be in a better position. i may change it to a threaded knob which gives the saw a larger area to rest on. my only real complaint would be the pivot. if you don't pay attention, it can work loose which lets the saw wobble. i tightened it a second time to take out the wobble. this had the additional effect that the saw will stay at any position you leave it rather than dropping to the undersized stop and you don't have to raise it completely to the upright position. all that said, once i learned the quirks of this tool it works well. i should get a lot of services from it.
November 15, 2011
Rated 4.0 out of 5.0 by Rick All & All pretty good product
There are a couple of things I didn't like. One is the chain vise,don't like it's location at all,parts of it are below the base.Would have rather had it like there chop saws.The other is I had to sand a lot of the paint off all around the chain vise to get it to work,chain wouldn't even go through where you need to work it.One other thing,not as portable as I thought it would be,very heavy.Was going to use it on my weld truck,too heavy,so I'll just use it in the shop instead.Heavy is also good,built nice.
January 1, 2013
Rated 4.0 out of 5.0 by CatMan1874 The Table allows you to have clean vertical cuts in material.
By converting the portable band saw into a horizontal table saw with out investing on a second horizontal band saw. It has reduced the extra time machining the ends for square end material with a clean vertical cut. The only two draw backs I have found is the extra time it takes to get the portaband adjusted for true cuts on the material, and having a way to make clean angle cuts. In all this table saved about two weeks of extra machining. I give it a A+.
December 6, 2011
Rated 4.0 out of 5.0 by VDeck4 Good tool for the price
I was originally looking for a chop saw that would cut metal conduit, uni-strut and threaded rod. My company already had several Milwawkee portable band saws, so this was a great alternative. It is easy to put together and take apart.
July 16, 2013
Rated 1.0 out of 5.0 by Jim52 Casting broke first use, Milwaukee repair factory repair - no warranty, Home Depot refund
Casting on swing-arm broke first use. Drove 50 miles to Milwaukee Factory Service Center - no warranty on accessories, no parts available, call someone like Home Depot that cares. Got refund from Home Depot. No more Milwaukee tools.
November 27, 2012
Rated 1.0 out of 5.0 by Falcon Review
Have not used yet due to part#25[Work Piece Stop] missing. When I do get to use it I will have to grind slot out for chain to pass through it. Still waiting on part.
December 14, 2012