Rated 3.6 out of 5 by 8
Rated 4.0 out of 5.0 by Retroguy Old Tyme Porch Ceiling
I was opening up a previously enclosed porch and wanted to regain the originality that the house had in 1929. I had this unsightly ceiling to repair. After pricing tongue and groove beadboard this fit my budget. I took my time and stained it dark, gave it 2 coats of marine varnish. It's not a one person job even with a 2x4 lift holding it in place. It came out beautiful and you'd be hard pressed to know it wasn't there since the house was built.
May 29, 2016
Rated 4.0 out of 5.0 by Product It'll do
I knew that the wood wouldn't have to be perfectly matched because of height and location. I do wish that I had set aside the time to really pick through the pieces. The joints are a little sloppy so install techniques took a little fussing and tweaking. In this case because I was installing overhead, I testing my pieces in a run before tacking up. Be prepared to sand and put your gloves in your pocket before your trip to your favorite HD!
December 6, 2013
Rated 5.0 out of 5.0 by Hammmer Choose your own!
I like this for a lot of projects. Requires minor sanding and finishing with your own choice of stain, poly, etc. Good for the DIYer that isn't intimidated by finishing their own wood. You'll save $ in the end. Worked well for my families needs. Blessings to All. Don't let an associate pick for you or you'll regret it.
June 15, 2015
Rated 4.0 out of 5.0 by jppk Ceiling install
After my roof rotted I needed to replace the interior ceiling in the living room. The room previously had 3in of exposed beams with acoustic tile inbetween.After the roof re-do most of the space was filled with spray foam so we cut this product into 2ft strips and nailed it to the beams.
Though it's not recommended I covered it with two coats of polycrylic rather than paint. I have yet to cover the joints with trim but it's on the list. Have to say, it looks ok...(more
However, it does require a non-trivial amount of sanding so be sure to invest in or borrow a good orbital sander. Also, when moving wear gloves it splinters like nothing I've ever seen. Also, make sure you pick out your own boards because many are damaged.
February 27, 2013
Rated 3.0 out of 5.0 by Groversmith1 Decent alternative to t&g
This is better as a concept. I used it for a shed ceiling and its an economical alterative to tongue and groove. It was surprised at its flexibility; i torqued it pretty intensely getting it into my car and dropped a bunch of junk on it and it didnt crack or split. Aesthetically, it is just good enough. There is no way it could take a stain, as any gap or inconsistency is filed in with glue (or putty). That said it is just good enough for non-critical spots.
April 29, 2014
Rated 4.0 out of 5.0 by HONESTABE Good Buy!
I have used this plywood panels on many occasions, for walls in kitchen you can prime and paint. I just stained saved a ton and quike to install cut /liquid nails/ finish nails great to go over old plaster walls. I have installed on ceilings in entrence and walls this is a landlords good friend!
August 15, 2014
Rated 4.0 out of 5.0 by misterjefferson Pretty decent stuff
If you pick through a stack of this beadboard ply, you can find some decent pieces without cracks or blemishes. It has been ideal for my basement walls, with just a quick coat of waterproofing. The only problem I had was that the laps didn't fit exactly, with the under side being longer than the exposed side, leaving a small but very noticeable extra space between sheets.
October 26, 2012
Rated 1.0 out of 5.0 by Dolan Ply board difficult
Edges of this board is not consistent. You will a lot of time trimming the laps here.
June 27, 2013