Model # 034-0197RP

Internet #202592809

Powermate 100 - 130 psi Pressure Switch
0846212004579

Powermate

100 - 130 psi Pressure Switch

$25.06 /each

Frequently Bought Together

Product Overview

The Powermate pressure switch is part of the large line of Powermate genuine replacement parts. A pressure switch regulates air pressure in the compressor. Replace a pressure switch with a new Powermate pressure switch if the compressor motor is cutting out or not turning on at the proper psi.

  • 100 - 130 psi
  • 4 port with bleeder
  • Powermate pressure switch is durable and long lasting
  • New Powermate pressure switch allows air compressor to run at its most efficient capacity, turning on and off the motor at the correct psi

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

can I set this switch up to cut on at 70 and cut off at 100

Asked by: tommy
No, this one was preset to 100 psi on and 130 psi off. There no instructions for making adjustments to those settings.
Answered by: macxxxx
Date published: 2016-04-10

Does this switch operate on 110v or 220v?

I have a 60 gallon single stage compressor Campbell Hausfeld 220v
Asked by: grumpy4x
I used it for 220 V. You could use just one pole of the switch for 110 V.
Answered by: macxxxx
Date published: 2016-01-15

Does bleeder bleed pressure off of compressor so it can start easier?

My old Campbell Hausfeld has a check valve and bleeder. Can the bleeder tube be hooked to this switch?
Asked by: Anonymous
No sounds like your check valve or safety release might be leaking. Spray with soapy water to check for leaks. The 1/4 inch sensing line should come from the main tank pressure.
Answered by: Rhino
Date published: 2016-01-15

when my compressor reaches max air the presure switch bleeds down then it kicks back on why

Asked by: Anonymous
You might have a leak Spray with soapy ware after you unplug the unit.
Answered by: Rhino
Date published: 2016-01-15
  • y_2017, m_2, d_25, h_24CST
  • bvseo_bulk, prod_bvqa, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_, sid_202592809, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=BEST_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=POSITIVE_ANSWER_FEEDBACK_COUNT, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 54ms
  • QUESTIONS, PRODUCT

Customer Reviews

100 - 130 psi Pressure Switch is rated 4.3 out of 5 by 17.
Rated 5 out of 5 by from Works great Pressure settings are dead on and handles my 3HP motor with no issues.
Date published: 2016-12-27
Rated 4 out of 5 by from Adapted to my compressor The bad switch on my compressor is no longer available. I bought this one as it was as close as I could find. I broke the rules and adjusted the pressure a bit. The switch perporms exactly as I needed. I imagine the "do not adjust" warnings are for the lawyers benefit. .
Date published: 2011-07-09
Rated 3 out of 5 by from Compressor pressure switch The switch wire up differently the original one so make sure to ohm test before wiring it up. The compressor doesn't kick on till about 80psi but shuts off right at 130 psi. I messed with the switch trying to get it to kick on at a lower so I'm sure it voided the warranty but other than that it works great! If it kicked on at a higher pressure it would have gotten a much better rating.
Date published: 2016-04-05
Rated 3 out of 5 by from So far it works great. However, I could not remove a pre-installed pipe plug. I have no complaints on the quality appearance and operation of the switch so far. However, it came with a pipe plug installed in one of the ports. When I tried to remove it, the broach stripped. I was confused why it would be so tight and why it was installed when it came with 2 additional spare plugs in a bag. Anyways, I got everything to work by using a T to make up for the lost port. I should probably add that I used this switch on an older air compressor of a different brand... so maybe the port was supposed to be plugged.
Date published: 2014-02-13
Rated 5 out of 5 by from PSI Pressure Switch This was the easest pressure switch I have ever installed. There are four sets of screws on the switch for power. The top set of screws is power or line. the bottom set of screwss are for the motor and they are marked motor. The flex line coming off of the tank attaches to the air line in the bottom of the switch.
Date published: 2014-07-29
Rated 5 out of 5 by from Fast and easy great price, fast delivery easy to install/ I would order again online
Date published: 2015-11-03
Rated 5 out of 5 by from perfect! this is great original part! i would reccomend this to anyone who needs one!
Date published: 2013-10-01
Rated 5 out of 5 by from Good quality Good quality easy to use good instructions works well and easy to adj
Date published: 2013-11-05
  • y_2017, m_2, d_24, h_15
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_17
  • loc_, sid_202592809, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 56ms
  • REVIEWS, PRODUCT