Free Shipping and BOPIS


Model # 1000

Internet # 203204054

Shingle Shark with Offset Guide

This item has been discontinued.
The Home Depot no longer carries this specific product.

$299.99 /each



Model # 1000

Internet # 203204054

The Qualcraft shingle shark is designed to allow for accurate and repeatable cuts at any angle, as well as lengthwise cuts for a starter course used along the edge of the roof. It has two offset holes, one for America and one for US shingles. The crosscut guide adjusts a full 180 degrees for any angle, cuts face up or face down and from either the top or bottom edge. It can be set up by using a cleat to prevent slippage, using a piece of two-by-ten lumber and footing the tool against it, or by using a 6 in. x 90-degree roof bracket.

  • Cuts both asphalt or fiberglass shingles at any angle
  • Cold rolled steel construction with powder coat paint finish
  • Self cleaning arm
  • Open mesh table allows the weight of the unit to be 38 lb.
  • Mounts on roof 3 different ways


Product Depth (in.) 
Product Height (in.) 
Product Width (in.) 
Commercial / Residential 
Commercial / Residential 
Product Weight (lb.) 
52 lb 
Roofing Product Type 
Roofing Tool/Accessory 
Tool/accessory product type 
Tools & Accessories Product Type 
Other Tools & Accessories 
Warranty / Certifications
Manufacturer Warranty 
Qualcraft industries warrants to the purchaser that all products are free from defect in material and workmanship at the time of shipment. Obligation under this warranty is limited to product replacement for the period of (2) years. 


Rated 4.5 out of 5 by 4 reviewers.
Rated 5.0 out of 5.0 by qualcraft shingle shark It works great when properly adjusted. Ive seen some reviews where the blade is said to wear out quickly. I myself got the item and tried it right out of the box and soon realized the blade was too tight towards the tip. I decieded to look at the directions and it says, the cutting blade should barely touch the base. It really doesnt have a sharp blade, its more like a dull paper cutter, but works fantastic. The adjustment made a huge difference in cutting straight and the effort to make those cuts. It makes cutting angles for valleys, starter shingles, and diagonal starter (books) sets straight and quick. If you don't want to read instructions and use right out of the box you will not get the full potential of this tool. It will wear out quickly because its metal on metal and will not cut straight. It doesnt take alot of time to adjust but you will need two adjustable wrenches to move the jamb nut on the spring and they give you an allen wrench with the tool for the other set screws. Just some other advice I also needed to loosen the jam nut and other allen set screws all at once. Then gave the handle afew ups and downs to set the placement on the rear of the blade before tightening the allen bolts and resetting the jam bolt. I found it makes shingling a better experience and produces nice straight cuts. I cant say it lasts forever because I've only used it on a few projects, but so far its been a time saver. August 5, 2014
Rated 5.0 out of 5.0 by great product works great wish it had a longer fence with measurements on. March 27, 2013
Rated 3.0 out of 5.0 by shingle shark the tool works fine although there are a few things that could easily be improved on , such as the locking pin which will jam the shingle, Also needs a larger tray to cut angles on steep pitch roofs. October 5, 2012
Rated 5.0 out of 5.0 by Great product. A real time saver Would recomend this to anyone. Cuts shingles like paper. October 9, 2012
  • 2015-08-01T11:15:57.264-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_4, tr_4
  • loc_en_US, sid_203204054, prod, sort_default
1-4 of 4


Standard Shipping includes delivery by small parcel service. Processing time varies by product.

If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.