0648846000473

RIDGID

Model EB4424

Internet #100061671

Store SKU #428230

Oscillating Edge/Belt Spindle Sander

$199.00 /each
  • Lifetime Service Agreement with Registration
  • Tool free conversion from belt to spindle sander
  • On-board accessory storage

Frequently Bought Together

Product Overview

Rigid Hero
Feature 1

Tilting table goes up to 48 degrees, with detents at popular angles (0, 15, 22.5, 30 and 45 degrees) to sand bevel edges

Feature 2

No tools required to convert from belt to spindle sander

Feature 3

Accessories can be stored on board

Specification Icon


amperage

______________________________

4.6 amps

Specification Icon


spindle speed

______________________________

1,725 rpm

Specification Icon


belt speed

______________________________

1,350 rpm

Specification Icon


Warranty

______________________________

3 year

OR LSA

Free Shipping to home or store

ON POWER TOOL AND ACCESSORY ORDERS OVER $45

Constructed as two tools in one, the RIDGID Oscillating Edge/Belt Spindle Sander operates with rotary and oscillating motion to help you effortlessly achieve burn-free finishes on edges, contours, faces, inside curves and outside curves. The tool-free conversion from belt to spindle helps you quickly and easily make changes, so you can complete multiple jobs in the time it would take for one. For your convenience and to help keep your work area neat, the onboard accessory storage neatly holds the belt mechanism, washers and more.

California residents: see   Proposition 65 information

  • Includes a 4 in. x 24 in. belt, all drums and a set of sleeves
  • 5-Amp, 3/8 hp motor to supply power for high performance and excellent results
  • Up to 1725 RPM spindle speed
  • 60 OPM for speedy sanding action
  • Ball bearing construction for smooth operation and longevity
  • Built-in sawdust collection port to help keep your workspace and air clean
  • Lockout power switch to help prevent unintentional activation
  • 8 ft. cord for long reach to where you need it
  • Table that tilts up to 48 Degree with detents at the most popular angles (0 Degree, 15 Degree, 22.5 Degree, 30 Degree and 45 Degree) to sand bevel edges
  • 3-year limited manufacturer warranty
  • Lifetime service agreement with RIDGID with registration within 90 days of purchase (begins after the warranty period expires)
  • Note: Product may vary by store
  • Click Here to Register Your Product

    Test Item

  • Click here for more information on Electronic Recycling Programs

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents.  Download a free copy from the Adobe Web site.

Specifications

Dimensions

Details

Warranty / Certifications

More Products With These Features

Search

Customer Questions & Answers

51 Questions285 Answers

Customer Questions & Answers

Oscillating Edge/Belt Spindle Sander
Oscillating Edge/Belt Spindle Sander

Ask your questions. Share your answers.

 
 
Clear Search Term
 
 
Sort By:
 
11 answers

The tighting nut just spins

This question is from Oscillating Edge/Belt Spindle Sander
Asked by
Clinton, Tn
Read all my Q&A
August 10, 2014
I installed the belt sand to my Oscillating Edge/Belt Spindle Sander. I am finished using it and wanted to remove it but all the unlocking nuts just spins and I cant remove the belt sander. Does any one have any ideas on how to remove this nut?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (11)

Asked by
Roanoke, Il
Read all my Q&A
March 24, 2015
Answer: 
must be stripped out, your tightening it to tight
-1point
0out of 1found this answer helpful.
Was this helpful?helpful0unhelpful1

Asked by
Hilo Hawaii
Read all my Q&A
Home Improvement Profile: DIYer
January 14, 2015
Answer: 
If you are talking about the nut that holds the unit to the shaft, just hold the spindle from spinning and turn to the right. It is a left hand thread.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
SE Arizona
Read all my Q&A
Home Improvement Profile: DIYer
January 13, 2015
Answer: 
It is a left-handed thread, so to loosen it make sure you are turning it clockwise. If the threads are stripped, maybe Ridgid's lifetime warranty will cover that.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Garden Grove
Read all my Q&A
Home Improvement Profile: DIYer
August 12, 2014
Answer: 
We are talking of the top plastic coated center nut that holds on the assembly right. This nut is reverse threaded so it lefty tighten and righty loosen. Could you have stripped it when you installed the belt assembly? If it is stripped, you'll have to cut it off without hurting the rod threads with a cut-off wheel on a grinder. It's a brass nut so it will cut through fairly easily with an abrasive wheel Read More
We are talking of the top plastic coated center nut that holds on the assembly right. This nut is reverse threaded so it lefty tighten and righty loosen. Could you have stripped it when you installed the belt assembly? If it is stripped, you'll have to cut it off without hurting the rod threads with a cut-off wheel on a grinder. It's a brass nut so it will cut through fairly easily with an abrasive wheel on a Dremel type grinder if you have one. You'll have to order a replacement from Rigid. If you cut the rod threads then you'll need the whole rod assembly replaced. This is all based on your description of the problem. Read Less
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Read all my Q&A
August 12, 2014
Answer: 
Thank you for your interest in RIDGID!
The knob nut that secure the belt sander assembly in place is left hand threaded and screws onto the sanders main spindle. You need to insure that the belt sander assembly is properly seated in the unit, which will allow it and the spindle to lock together, then the knob nut should rotate off in a clockwise direction while holding the belt sander assembly by hand, Read More
Thank you for your interest in RIDGID!
The knob nut that secure the belt sander assembly in place is left hand threaded and screws onto the sanders main spindle. You need to insure that the belt sander assembly is properly seated in the unit, which will allow it and the spindle to lock together, then the knob nut should rotate off in a clockwise direction while holding the belt sander assembly by hand, to keep the spindle from turning. If you are not able to resolve the problem with the above information, the sander will need to be taken or sent in to a local service provider to be checked and the problem resolved.
Regards,
RIDGID
Read Less
+8points
9out of 10found this answer helpful.
Was this helpful?helpful9unhelpful1

Asked by
Bentonville, VA 22610, USA
Read all my Q&A
Home Improvement Profile: DIYer
August 12, 2014
Answer: 
Hopefully the threads are not stripped. The nut is a reversed thread, so you may be turning in wrong direction.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Huntington Beach, CA
Read all my Q&A
August 12, 2014
Answer: 
That does not sound right. I know the nut turns in the opposite direction of a normal nut, but it should still tighten/loosen. You might want to return the unit to the store.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
August 12, 2014
Answer: 
There is only one nut to remove and it has left hand threads. It would be best to refer to the instructions in the manual. If you do not have a manual you can download one from the sanders product page on Home Depot's website. You can also download the manual at Ridgid's website.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Wheat Ridge, CO
Read all my Q&A
August 11, 2014
Answer: 
Roger, hold the big tube end of the sanding paper to keep it from spinning with your left hand. Then with your right had turn the top knob in the direction of the unlock symbol / clockwise. It will then to take maybe a little more pressure than one might think.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Mohave Valley, Arizona
Read all my Q&A
Home Improvement Profile: Professional
August 11, 2014
Answer: 
ive read lots of reviews on this problem, with it not un screwing, even with vice grips, thats why i always loosen mine after use. it just spinning i never heard of. if the wing nut that you take off to remove the sander mech is what your talking about, well sounds like the gears ares stripped. the shaft that it screws to shouldnt move, letting you loosen it. they come with a life time warranty so id Read More
ive read lots of reviews on this problem, with it not un screwing, even with vice grips, thats why i always loosen mine after use. it just spinning i never heard of. if the wing nut that you take off to remove the sander mech is what your talking about, well sounds like the gears ares stripped. the shaft that it screws to shouldnt move, letting you loosen it. they come with a life time warranty so id take it back to home depot. Read Less
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Aromas, CA
Read all my Q&A
Home Improvement Profile: DIYer
August 11, 2014
Answer: 
The nut is a "backwards" thread. Hopefully you didn't reverse the thread.
-1point
0out of 1found this answer helpful.
Was this helpful?helpful0unhelpful1
 
11 answers

How are other owners keeping the sleeves from slipping off the larger drums?

This question is from Oscillating Edge/Belt Spindle Sander
Asked by
Davenport, FL
Read all my Q&A
July 10, 2014
I have been relatively successful with slipping carefully measured scraps of paper or fine grit sandpaper between the rubber and the sleeve, but the 2" sleeve is driving me nuts. I think the Diablo Sleeves are a few thousandths larger. Give me some of your ideas.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (11)

Asked by
california
Read all my Q&A
November 4, 2014
Answer: 
never have that problem, just use the largest washer on top of the spindle and make sure its tight enough.
-1point
0out of 1found this answer helpful.
Was this helpful?helpful0unhelpful1

Asked by
Connecticut
Read all my Q&A
October 4, 2014
Answer: 
Try wrapping some masking/ painters tape once or twice around the rubber. This has worked well for me.
-1point
0out of 1found this answer helpful.
Was this helpful?helpful0unhelpful1

Asked by
Huntington Beach, CA
Read all my Q&A
August 12, 2014
Answer: 
I've not had this problem, but a larger washer that physically holds down the sleeve would help.
-2points
0out of 2found this answer helpful.
Was this helpful?helpful0unhelpful2

Asked by
Wheat Ridge, CO
Read all my Q&A
August 11, 2014
Answer: 
I think it's a bit of an art but find that if I just turn the belt adjustment knob slowly I can find the balance point - the point at which the belt stops moving up or down on the spindle and just stays in place. Usually doesn't take too long after a little practice.
+2points
3out of 4found this answer helpful.
Was this helpful?helpful3unhelpful1

Asked by
Mohave Valley, Arizona
Read all my Q&A
Home Improvement Profile: Professional
August 11, 2014
Answer: 
i couldnt so i called the manufacture and had them send me 6 of there belts, the exact ones they include with the sander. they seeem to be the only ones that wont constantly move up and down.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Aromas, CA
Read all my Q&A
Home Improvement Profile: DIYer
August 11, 2014
Answer: 
Tightening the top nut should expand the rubber to take up any gap between the sandpaper & the rubber drum.
+4points
5out of 6found this answer helpful.
Was this helpful?helpful5unhelpful1

Asked by
Davenport, FL
Read all my Q&A
July 14, 2014
Answer: 
Answering my own question. The 2" rubber drum is 1.936" in diameter. The 2" Diablo Sleeve is 2.003" on diameter. Thats 0.067 difference. I had to sandwich 2 pieces of Adhesive Back 220 grit, back to back to get it to tighten. I did a review on Diablo's sleeves. It states they are too big for this sander. Try Ridgid Sleeves on Amazon as HD does not sell them anymore.
+5points
5out of 5found this answer helpful.
Was this helpful?helpful5unhelpful0

Asked by
DENVER
Read all my Q&A
July 11, 2014
Answer: 
Make sure you have the proper sized washer on the top of the drum, tighten the nut a little tighter and don't press the wood into the sleeve as hard. This usually works for me.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Bflo, NY
Read all my Q&A
Home Improvement Profile: Professional
July 11, 2014
Answer: 
I'm still using the stock sleeves, but it might be feasible to take up some gap with painters tape (removable). If tackiness is all that's needed a shot oh repositionable spray mount (Krylon or 3M) make it. Can be had at art or office supply stores.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Read all my Q&A
July 11, 2014
Answer: 
Thank you for your interest in RIDGID!
There is not a recommendation or customer indicated means for keeping sanding sleeves from slipping on the rubber spindles that we are aware of or can advise of, since it is not something that we have received reports of as being an issue with the sander from other customers. You may want to try some sanding sleeves from 3M, Norton, or another manufacturer, if the Read More
Thank you for your interest in RIDGID!
There is not a recommendation or customer indicated means for keeping sanding sleeves from slipping on the rubber spindles that we are aware of or can advise of, since it is not something that we have received reports of as being an issue with the sander from other customers. You may want to try some sanding sleeves from 3M, Norton, or another manufacturer, if the Diablo sleeves you are using are not staying on the rubber spindles when the spindle washer is installed and the spindle retainer tightened to compress the rubber spindle, which then holds the sanding sleeve in place under use.
Regards,
RIDGID
Read Less
+4points
7out of 10found this answer helpful.
Was this helpful?helpful7unhelpful3

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
July 11, 2014
Answer: 
I haven't seen this problem. Clean the drums with mineral spirits. You may need to look for a different manufacturer for the sanding sleeves if cleaning doesn't work. It sounds as if they were made slightly too big.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
 
11 answers

Can it grind metal

This question is from Oscillating Edge/Belt Spindle Sander
Asked by
Read all my Q&A
April 3, 2014
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (11)

Asked by
Roanoke, Il
Read all my Q&A
March 24, 2015
Answer: 
yes but machine must be clean from saw dust
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Pinehurst, NC
Read all my Q&A
January 26, 2015
Answer: 
Not really. Perhaps very light touch on non-ferrous.
-2points
0out of 2found this answer helpful.
Was this helpful?helpful0unhelpful2

Asked by
SC
Read all my Q&A
Home Improvement Profile: DIYer
January 25, 2015
Answer: 
You would need to get a sanding belt made for metal. It should do light metal ok, It is intended for wood.
-1point
1out of 3found this answer helpful.
Was this helpful?helpful1unhelpful2

Asked by
Mohave Valley, Arizona
Read all my Q&A
Home Improvement Profile: Professional
August 11, 2014
Answer: 
no
-6points
0out of 6found this answer helpful.
Was this helpful?helpful0unhelpful6

Asked by
Millville, PA 17846, USA
Read all my Q&A
April 22, 2014
Answer: 
You can finish anything that you can finish with sand paper.
+5points
5out of 5found this answer helpful.
Was this helpful?helpful5unhelpful0

Asked by
Huntington Beach, CA
Read all my Q&A
April 15, 2014
Answer: 
I'm not sure if you are supposed to grind metal with it, but I did and it worked. I polished up some 1/2 x 1/8 in steel strips inlayed into wood on the belt attachment. I think the biggest issue would be to make sure your sanding medium is appropriate..
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Garden Grove
Read all my Q&A
Home Improvement Profile: DIYer
April 7, 2014
Answer: 
Yes, with the right abrasive belts and drums. But it won't take a lot of pressure if you try to remove a lot of material at one time. It will work as a surface finisher with light pressure. Try open coat abrasives and let the machine's belt speed and movement do the work.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
SE Arizona
Read all my Q&A
Home Improvement Profile: DIYer
April 4, 2014
Answer: 
this sander is designed for wood, and the belts are made for wood. I suppose it could sand a soft, non-ferrous metal like aluminum or brass, but a grinder that is designed for metal is so much less expensive and would work better.
0points
1out of 2found this answer helpful.
Was this helpful?helpful1unhelpful1

Asked by
Aromas, CA
Read all my Q&A
Home Improvement Profile: DIYer
April 4, 2014
Answer: 
It will sand metal. That is a loaded question, however. It is NOT a grinder, it IS a sander. I use it to do minor shaping/finishing on metal parts from time to time. It is not suited for large material removal (in metal). Does great to finish edges on aluminum, brass, copper & some steel; thickness dependent. The more agressive you try & be with it, the faster you will wear down the sanding belts. Also, Read More
It will sand metal. That is a loaded question, however. It is NOT a grinder, it IS a sander. I use it to do minor shaping/finishing on metal parts from time to time. It is not suited for large material removal (in metal). Does great to finish edges on aluminum, brass, copper & some steel; thickness dependent. The more agressive you try & be with it, the faster you will wear down the sanding belts. Also, you may want to purchase a belt that is suited for metal applications. Read Less
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0

Asked by
Wheat Ridge, CO
Read all my Q&A
April 4, 2014
Answer: 
No, it comes with sand paper rolls - not the best for grinding metal. I wouldn't use it for metal unless they come out with a model made specifically for that.
0points
1out of 2found this answer helpful.
Was this helpful?helpful1unhelpful1

Asked by
DENVER
Read all my Q&A
April 4, 2014
Answer: 
Sure, if you don't mind voiding the warranty and destroying the moving parts! (It's a woodworking tool)
+1point
3out of 5found this answer helpful.
Was this helpful?helpful3unhelpful2
 
11 answers

Is there a dust collection port/attachment?

This question is from Oscillating Edge/Belt Spindle Sander
Asked by
Oskaloosa, IA
Read all my Q&A
February 11, 2014
Can I connect my shop dust collection system to this unit? If so, what size is the port?
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers (11)

Asked by
Hilo Hawaii
Read all my Q&A
Home Improvement Profile: DIYer
January 14, 2015
Answer: 
Yes
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Mohave Valley, Arizona
Read all my Q&A
Home Improvement Profile: Professional
August 11, 2014
Answer: 
you can connect it to your shop vacuum. yes
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Millville, PA 17846, USA
Read all my Q&A
April 22, 2014
Answer: 
You can connect it. The port is 2-1/2" outside.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Huntington Beach, CA
Read all my Q&A
April 15, 2014
Answer: 
Yes you can use your shop vac. I believe it fits the normal 4 inch tube.
Mike
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
DENVER
Read all my Q&A
April 4, 2014
Answer: 
Yes. It has a 2 1/2" fitting for a shopvac on the back side.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Read all my Q&A
March 4, 2014
Answer: 
its one on the back a 2 1/2'' but it dont catch a lot of the dust you can build a extra one for the top r rig up one as i have shown u tube may have more on this but its a good sander
User submitted photo
+6points
6out of 6found this answer helpful.
Was this helpful?helpful6unhelpful0

Asked by
Read all my Q&A
February 25, 2014
Answer: 
The port size is 2.5 inch, so you may need adapters depending on your dust collection hose size. Most adapter from shop vacs will work.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
Marco Island, FL, USA
Read all my Q&A
February 18, 2014
Answer: 
Yes, 2 1/4
0points
1out of 2found this answer helpful.
Was this helpful?helpful1unhelpful1

Asked by
Artesia, NM 88210, USA
Read all my Q&A
February 18, 2014
Answer: 
Yes
+3points
4out of 5found this answer helpful.
Was this helpful?helpful4unhelpful1

Asked by
Aromas, CA
Read all my Q&A
Home Improvement Profile: DIYer
February 12, 2014
Answer: 
Yes; 2-1/2"
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0

Asked by
SE Arizona
Read all my Q&A
Home Improvement Profile: DIYer
February 12, 2014
Answer: 
Yes, there is. It fits the standard 2 1/2" hose used by the Rigid Vacuum, as well as others. I have it hooked up to my dust collection system, which collects most of the dust. I have also mounted an additional dust collector hose with a jointer dust collector plate to the left edge and that picks up almost all of the dust.
+3points
3out of 3found this answer helpful.
Was this helpful?helpful3unhelpful0
2 3 4 »
  • 2016-08-29 T15:14:38.944-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_100061671, prod, sort_default
2 3 4 »
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 256ms
  • QUESTIONS, PRODUCT

Customer Reviews

Rated 4.3 out of 5 by 361 reviewers.
Rated 1.0 out of 5.0 by Bad Motor right out of the box I purchased this yesterday at about 4 PM. I took it home, assembled it and tried to turn it on. It only hummed loudly. I double checked the installation of the 2" drum I installed and it turned very freely. I tried again and it only hummed. I packed it up and returned it for another one and the service people were extremely courteous and helpful. I picked up another one and tested it there. I have the second one home now and so far it works just fine. I read on the Ridgid website others had a problem with bad motors as well. I do recommend this product because of the name and because of the Home Depot Service Reps. August 28, 2016
Rated 4.0 out of 5.0 by pretty good tool It is a pretty good tool. It does an array of things such as straight edge sanding and then can become a spindle sander. I give it 3 stars for quality because it has a lot of plastic in it and no cast iron top. August 16, 2016
Rated 5.0 out of 5.0 by Excellent It really is an excellent machine for me, simple and quick to change the band, and adjust it ... very simple and eficiente.l! August 9, 2016
Rated 4.0 out of 5.0 by Good machine Worked great out of the box. Nice having 2 tools in one August 16, 2016
Rated 1.0 out of 5.0 by Took the plunge, got all wet. First off, I am in love with the idea of this machine. It is super convenient to have two machines in one. I found the table to be sturdy and the size of the machine well proportioned. The belt sander attachment was a little wobbly but sanded smooth/flat surfaces. I am a big believer in user reviews. I figured I would take the plunge and go against the "complainers" of this product. Thankfully HD gave me a full refund and unfortunately an opportunity to join the complainers. In short, right out of the box, with my family watching in anticipation, I flipped the switch and just heard the buzz of the motor trying to get the spindle turning. Flipped it off/on a few times, still just a humming machine with no turn. I decided to give it a spin with my hand and it finally started turning. Something in the motor housing rhythmically clicked with the spindle turns. Interestingly enough, if I laid the unit on its side (on the side of the on/off switch) the unit fired right up and spun effortlessly with no clicking. So, needless to say, having to turn the entire unit on it's face every time I want to sand something is not going to happen. The unit never did start/spin with the on/off switch, I always had to hand turn it while it was on but not turning the spindle. If they ever decide to make this unit more dependable, I will definitely buy it again. Hey Rigid, let me know if you have any suggestions on alternative units. Thanks so much. goodwoodbytopher dot com August 18, 2016
Rated 5.0 out of 5.0 by Pure excellence This is the best sanding unit I've ever used. Buy it ... now. July 18, 2016
Rated 1.0 out of 5.0 by not enough power and too noisy I like the concept of having a spindle and belt sander combined in one unit but ridgid did a poor job designing its version of what a spindle and belt sander should be like. It doesn't have any real power, it stalls very easy when the slightlest pressure is applied to the belt and it's very noisy. I'm kinda surprised other manufacturers haven't designed a version of their own. The best thing about it is it is convenient to have two sanders in one unit, it saves time and space. July 10, 2016
Rated 3.0 out of 5.0 by Good Sander After reading other reviews, i decided to purchase the sander. Set-up is easy and straihtforward. However, intstalling the belt sander and making adjustments is tricky. After several minutes, the belt sander was installed. My first use was on a small box made out of poplar and oak. I was smoothing out the corners when the belt sander tore apart in half. I couldnt understand why. Maybe it was a cheap belt sander or the several minutes of installing the belt sander was incorrect. I will try another name brand belt sander and see if it performs better. June 28, 2016
  • 2016-08-29 T16:20:00.928-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_361, tr_361
  • loc_en_US, sid_100061671, prod, sort_default
2 3 4 5  ... 13 >>
  • bvseo_sdk, java_sdk, bvseo-3.1.1
  • CLOUD, getContent, 55ms
  • REVIEWS, PRODUCT