ROPPE Vinyl Self Stick Almond 4 in. x .080 in. x 20 ft. Wall Cove Base Coil-HC40C53S184 - The Home Depot


Model # HC40C53S184

Internet # 100183044

Store SKU # 432265

Vinyl Self Stick Almond 4 in. x .080 in. x 20 ft. Wall Cove Base Coil

ROPPE Vinyl Self Stick Almond 4 in. x .080 in. x 20 ft. Wall Cove Base Coil

This item has been discontinued.
The Home Depot no longer carries this specific product.
Please select another option below.

$18.97 / each


Model # HC40C53S184

Internet # 100183044

Store SKU # 432265

Store SO SKU # 629870

The ROPPE 20 ft. x 4 in. x 5/64 in. Almond Vinyl Self-Stick Wall Base Moulding is made to resist shrinking and separating from walls to help maintain a smooth and attractive appearance. Low cost and good looks highlight Roppe's Vinyl Base. It's extremely durable without sacrificing attractiveness, and very economical because it's made from PVC vinyl.

  • Economical vinyl construction
  • Almond color
  • Scratch-resistant semi-gloss finish helps resist scuffing and gouging
  • Resists shrinking and separating from the wall to help maintain a smooth and attractive appearance
  • Smooth pattern creates a finished edge between the floor and wall
  • Self-stick adhesive helps ensure a tight fit against walls
  • 20 ft. Length


Assembled Depth (in.)  240. in  Assembled Height (in.)  .08 in 
Assembled Width (in.)  4 in  Product Length (in.)  240 
Product Thickness (in.)  .080 in  Product Thickness (mm)  2.032 
Product Width (in.) 
Color Family  Beige/Bisque  Color/Finish  Almond 
Commercial / Residential  Commercial / Residential  Coved/Toeless  Coved 
Flooring Product Type  Cove Base  Indoor/Outdoor  Indoor 
Mark Resistant  No  Material  Vinyl 
Product Weight (lb.)  8 lb  Recycled Materials (%)  10 
Returnable  90-Day  Sold As  Roll 
Stain Resistant  No  Waterproof  No 
Warranty / Certifications
Manufacturer Warranty  Warranted for a period of one (1) year in accordance to Roppe's written instructions. 


Rated 3.3 out of 5 by 10 reviewers.
Rated 5.0 out of 5.0 by worked exactly as expected I purchased 2 -20 ft. rolls of this base and installed it in my mechanical room. I had read some of the "1-star" reviews before I installed it and have to say I was a little skeptical about trying this self stick product and even called Roppe Customer Service rep. who answered my questions and eased my concerns about going ahead with the installation. I laid the vinyl base out flat for 2 days, heated it a little with a hair dryer right before I stuck it to the wall, and the installation went great. No problem with it sticking to my freshly painted (Porter latex semi-gloss) drywall wall. This was my first experience with installing any kind of wall base and I won't hesitate using this one again. November 18, 2013
Rated 5.0 out of 5.0 by No problems I had no problems installing this vinyl baseboard. I left it unrolled for at least 24 hours before using and even heated it a bit with a hair dryer before installing, It went on very easily and has stayed attached to the wall. In fact, once it was pressed to the wall, it was impossible to reposition it. Not sure why the other reviewer had so many problems. Maybe it was old and the adhesive had dried out somewhat, or the surface was not properly prepared. I would not hesitate to use this product in the future, February 14, 2011
Rated 4.0 out of 5.0 by Vinyl review I purchased this moulding to protect water from going under the wall in my garage when washing down the floor. I applied it to fresh drywall that was painted with Dulux Satin finsh exterior paint.. Since it comes rolled up it is best to first unroll it and put something over the ends to keep it flat. When applying to the wall make sure that it is free of dust. Wipe the wall down with a solution of mild soap and water and dry with a towel. Starting from one edge of the wall, cut the end so it is square with edge, then unpeel part of the backing and stick to edge. Carefully align the bottom edge with the floor and peel the backing aprox 2' and lightly stick it to the wall. Continue until you reach the end of the wall and then cut carefully with scissors or razor knife. Now go back and check alignment, if satisfied then firmly press moulding against wall. Use a heat gun to any area where the glue is not adhereing well. Let stand 24 hours before washing. It is best to apply to non pourous textures such as ceramic. February 21, 2013
Rated 5.0 out of 5.0 by worked exactly as expected/hoped Unrolled the product and left it lay flat for 2 days. cut it to size, peeled backing off and installed. stuck right away and has remained in tact. Very easy! would purchase again. January 11, 2012
Rated 4.0 out of 5.0 by looks good, very basic moulding, easy to install Its been over a week since I installed this moulding, very easy to do and haven't had any major separation between the wall and vinyl moulding. I layed it out in the hallway (room temp. 70 deg. F) for over 24 hours, cut to size, heated with a hair dryer slightly, unpeeled the paper and stuck right away. Works good for the price, very basic. March 5, 2012
Rated 1.0 out of 5.0 by Disappointing Product Overall, installing this was a very unpleasant experience. I purchased four rolls to finish a newly constructed workshop with painted drywall and a concrete floor. Two of the rolls had defective adhesive that came off when the release paper was removed. After getting these replaced (and leaving them unrolled for 24 hours prior to installation), the actual installation proceeded smoothly. Unfortunately, by the next morning, most of the wall base had separated from the wall. The adhesive was still tacky, so I reattached the base and rolled over the surface with a hard roller to firmly bond the base to the wall. To no avail- by the next day, the base had separated again. Stick with a conventional baseboard. In the long run, its faster and less expensive... October 18, 2009
Rated 5.0 out of 5.0 by Self-stick wall base molding Shipped quickly, easy to install. Be sure to roll it out and let it become flat before securing to wall. July 15, 2014
Rated 2.0 out of 5.0 by Doesnt stick well at all The adhesive isn't that good at all. Especially if you have anything other than a smooth as glass wall to stick it to. I have a small amount of light texturing on the wall. Every other day I have to press it back down. Guess I'll have to buy some adhesive to apply to it and re-install.. May 5, 2014
  • 2015-03-30T10:08:39.349-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co-hasreviews, tv_10, tr_10
  • loc_en_US, sid_100183044, prod, sort_default
2 >>


Store Exclusive. This item is available for purchase in select stores only.