Rated 3.8 out of 5 by 215
Rated 1.0 out of 5.0 by HugoCH Cheap and nasty.
The motor may be fairly powerful, but that's about all you can say. The mitre gauge is not precise and there is considerable slop in the mitre slot. The mitre slots themselves are not standard width, so no accessories will fit, and they are not even a consistent width with themselves so a crosscut sled, for instance, will either have slop or will jam and not push through smoothly. The fence has to be measured carefully before every cut, because it won't lock perpendicular to the blade unless you take the time to do it yourself, nudging the back and front by fractions of an inch to get it straight. Good table saws can't be made this cheaply. If you can't afford a better one, save up, or get one used.
August 24, 2016
Rated 3.0 out of 5.0 by MashedPotatoes Decent enough
The quality of this saw is very high and it appears the value is excellent as well based on similar comparisons. I am a huge fan of Ryobi products and haven't had any trouble with them so far. Assembly takes about an hour and can be a tad tricky if you're unfamiliar with saws. Where I find the saw to fail miserably is the miter gauge, it's very loose and unstable. This is disappointing as I primarily purchased this saw for the miter gauge cuts. If you plan on doing any medium to large miter cuts this saw is probably not for you. Luckily Home Depot was generous enough to let me return it without hassle.
October 6, 2016
Rated 4.0 out of 5.0 by Michael395 Great for the home owner
This is by no means a professional table saw. There are nice, more feature laden table saws to choose from. But if you're just doing projects around the house and need to rip and finish cut pieces for that project, then save your cash and grab this little thing.
The fence leave a tad to be desired, but the measurements on the built in tape were pretty spot on. The fence, like I said, isn't all that great. You have to make sure it's straight and doesn't step out when you lock it down. A couple times doing it and you get the hang of it. If you really want a fence that works, get the yellow brand with the rack system fence. But bring your money bags because it's 3-4 times as much as this Ryobi.
October 18, 2016
Rated 3.0 out of 5.0 by s8nlilhlpr easy to assemble, adequate for my purposes. a tad on the flimsy side but it is what I expected for the price point. "safety arms" get in the way more than they help but are easy enough to sit out of the way.
October 25, 2016
Rated 3.0 out of 5.0 by WorkingGuy Needs some improvement
Some of the issues with the Ryobi 10" table saw include what appears to be a blade guard that is under the working surface of the table saw. due to position and width of the guard it makes it difficult to change out blades and doesn't allow for stacking blades. They only provide 1-Throat plate and due to the blade opening in the Throat Plate it doesn't allow for using a stacked blade set. In regards to the referencing of the throat and width, in the event you needed to remove the Throat plate the space that remains open does not provide for a continuous smooth feed.
The Blade angle adjustment is completely manual and the orientation of the release and locking arm makes it difficult to get an exact angle.
For the $$ it's good for small projects, standard usage and perhaps the Do-it-yourselfers.
September 28, 2016
Rated 3.0 out of 5.0 by Iwo not bad saw for the price and used for
had a little problem getting blade to 90 degree angle. Have used for limited time but found a major problem with throat plate not level with table. Almost impossible to cut non thru cuts of a consistent depth on narrow stock.
Saw there is no replacement for the plate so only way is to build up the plate. Difference is so small that I can only think of using layers of tape to build it up. Cannot use screws thru plywood as one person suggested since plate is not held with screws. Any suggestions??
September 22, 2016
Rated 5.0 out of 5.0 by Mudpuppy9 Durable and Accurate
Since molding and Qtr round cost so much, I have been ripping 2 x 4 studs to make my own. I have ripped enough to make all the trim for my brother's home remodel. This saw has handled the work admirably. I take the ripped lumber straight to the planer and then to the router. This Ryobi table saw has been my work horse. I have another table saw that cost a lot more, but I like my Ryobi better. Yes I recommend this saw to everyone. I have other Ryobi tools and I would give all of them a 5 Star rating.
October 3, 2016
Rated 3.0 out of 5.0 by painter saw
not a bad saw for the money. Has power and it seems to work well enough...
October 7, 2016