Rated 4.5 out of 5 by 399
Rated 1.0 out of 5.0 by pickycdn Save your money and skip this one
This nailer is a real piece of junk, you can find lots of people complaining about the same issues with the nailer dying after very short usage. I've had 2 die on my so far with less than 100 nails put through them. The driver blade eventually stops retracting, you can reset it manually by open the front snap and sliding it back, but after one more nail its stuck again.
I have lots of other ryobi products that have worked well but skip this one if you are planning to add to your collection go for the P325.
March 27, 2015
Rated 5.0 out of 5.0 by Domer Brilliant Product
Using this to add pine boarding to our dome ceiling. Running off existing batteries from other Ryobi products and it works a treat. Excellent product and the fact that it is cordless makes a world of difference, very little noise, like the lights at the side to show you where you are going to nail, easy to load, have tried several nail sizes with perfect results. I'm now waiting for the cordless Miter Saw that's being sent from the States since it can't be ordered through Homedepot.ca due to it being on backorder, it's in the mail as I speak.
September 8, 2014
Rated 5.0 out of 5.0 by 8FingeredPro Don't hesitate to buy this gun.
I received this gun today. I run a cabinet shop and have used 'many a gun'. I just loaded this thing with 2 inch brads, running off the smallest Li-ION battery they make. I placed a piece of 13/16 thick solid hickory over a piece of 5/8 thick solid red oak, over a 7/16 piece of 7 ply cabinet plywood and finally a piece of 13/16" thick solid 'soft' maple (total thickness of all a little over 2.5 inches). It drove the nail every time, one right after the other, all the way and countersunk just below the hickory top board. One nail ended just proud of the surface (see photo). Depth and pressure were set all the way, but still......air powered guns off the compressor wouldn't do much more if any. I usually have to set some nails a little more by hand in hickory before putty anyways. This thing is amazing.
April 15, 2014
Rated 5.0 out of 5.0 by CMG100 Another great tool from the Ryobi clooection
I purchased this tool a few days ago for some shelves I had to make. I was surprised by the power it packs...say goodbye to the hassle of an air compressor and hoses. It really does make your life easier owning this tool. It's easy to use for anyone and the features are pretty cool especially the LED lights. It doesn't drain the battery fast like i thought it would considering I have the compact lithium plus. Overall I'm glad I purchased it hopefully can purchase more Ryobi tools in the future to add to my collection.
March 2, 2014
Rated 5.0 out of 5.0 by SliceofPizza Nailed It!
I've been using this handy dandy cordless no muss no fuss nailer on a couple of projects. Adding shoe moldings to several rooms and most recently when assembling a built in bookcase project (still in progress.).
I wanted to comment that the P320 uses the same 18v battery as other Ryobi tools which is very handy and convenient when working on different projects.
So far I have used 1 inch long brads and 2 inch long finish nails without any problems or jams. I was somewhat skeptical about the power of the nail gun using the longer nails but rest assured no problem for this tool!
I love the little LED light that lights up when you position the head piece and are almost ready to drive the nail, I also love that you can adjust the pressure used although I have not had any reason to do so.
Highly recommend this very useful tool!
November 18, 2013
Rated 3.0 out of 5.0 by carpenter since day 1, you get what you pay for
I bought this nailer the first day it came out . I install trim and millwork for a living and used this gun for pick up the first 8 months. For The first gun the driver kept on getting stuck and would not shoot a brad. Had it repaired an took 2 months to get it back. When i got it back it worked the first day, then again it would not shoot a brad. Home depot exchange it for a newer one So months past an i say this gun works only when it wants to. This product is very frustrating for a carpenter i mostly use this on mdf casing an baseboard and i consistently have to pull out my nail set cause it wont set a 1 3/4 nail fully through, even with the 4 amp battery. It would shoot a nail then the driver would get stuck an ill have to reset it. Now it wont even fire when pressed down on material. Ive notice a lot of homeowners buy this gun and give it incredible ratings, well why not. If your not using this gun on a daily basis its good. I mean for constant use it tends to lose its power and the constant driver reset gets old. For the money its okay especially for homeowners who need it for little things so they dont have to deal with the air hose compressor issue. Its Bulky and heavy but you get used to it. Im ready to give the senco fusion a try which i should of got in the first place for my type of work
January 7, 2015
Rated 1.0 out of 5.0 by LC1builder Worst product yet produced by Ryobi
I own nearly all of the 18 volt Ryobi tools and a few electric portable hand tools. Most are very good and I haven't had any issues until i bought this brad nailer. This is my 2nd nailer and like other have mentioned. You start a project and shortly after it begins to misfire. I've done everything I know to try an determine the cause. I check for jams, ensure the battery is fully charged, inspect the nail chamber. To no available it continues to cycle but never fires a nail. Its very frustrating. It kind of sours me to even consider any 18 volt nailer of any brand. The cost is prohibitive. I expected rock solid reliability. It not happening with Ryobi...
December 23, 2014
Rated 5.0 out of 5.0 by Joecool My favorite tool
First off, I’m not a review guy. I really don't post on much of anything. I’ve always wanted a cordless nail (gun) er. I’m not a contractor just a diyer. My wife and me are renovating our home for the past several years. Working on the house a little at a time when not working, family, etc. I first saw them a few years back but could not justify the cost. But as the more projects I’ve done, the more I understood how versatile these tools are. Currently I’m doing window treatments i.e. cornices on all the windows on our home. 11 total. Yeah, it’s not the Taj or anything big. I’m using 3/4 mdf and 4 ¼ crowns for the top, various moldings for the middle and an end cap for the bottoms. Needed a small 5/8 nail for all the moldings so it does not poke through the back of the mdf. The first 2 cornices I did with 1 1/2 finish nails and 5/8 wire nails. That is Very difficult. I had to use small needle nose pliers to hold the wire nail while hammering it into place. That’s of course after I predrilled the hole for it and lets not forget I had to nail set it after I hammered it. And make sure you don’t miss with the hammer or let the nail set walk because that will be more touch up needed. Absolutely, ridiculously, time consuming for sure. As I started researching nail guns, I concluded that I did not want a compressor to lug around and didn’t want the noise either. I also didn’t want a fuel cell that adds extra cost and smelly fumes. This left me with very few options. This ryobi 18 gauge 18v and the dewalt 18 gauge 18v cordless. I believe as I write this, those are the only 2 manufactures that offer cordless nail guns that are 18v and don’t require fuel cells. After much researching I chose the Ryobi because it was substantially cheaper and used lithium batteries and not the older ni-cads. Coming from the Rc world I use lipo batteries all the time for my cars, helis, etc. I’m very familiar with the technology. I have my own 540 watt 30 amp psu and 400 watt 20 amp balance charger. I routinely parallel charge multiple lipos at once as well as balance charge them. The cool thing with the Ryobi is just charge and go. No settings to check or configure. When the lights stays green its ready. Lithium’s have a fantastic discharge curve compared to the older nicads, nihms, etc. And the power to weight ratio is fantastic as well. Point I’m trying to make is that I could not justify a substantial more amount of money for an older technology battery compared to the Ryobi. This is my first nail gun and did not have anything to compare it to and didn’t know what to expect. Phenomenal is what Ill say about this product. It saved me so much time and effort. It will make you smile and giggle like a schoolgirl on Christmas morning. My wife loves to shoot it as well. I waited a couple of weeks to really see how it performed before posting my review. I had to buy the lithium kit to go along with this nail gun. It was the P128 model. Keep in mind that the battery that came with this kit is the older lion battery without the fuel gauge. Model P102. They are rated at 24wh. That equals 24 Wh / 18 V = 1.33 amps. The newer batteries, the ones with the fuel gauge P107 are rated at 27 Wh. That equals 27 Wh / 18V = 1.5 amps. Even though I have the older non-fuel gauge battery, it is not a problem. When the battery gets low, the lights on the nail gun flash to let you know the battery needs recharging. That is very cool indeed. Also I averaged about 400 2 inch nails before needing to recharge the battery. And these nails were going into some very hard ¾ oak as well as 1 ⅛ stair treads and 1 ⅝ joist rafters! Not only did the gun seat the nail about ⅛ under all the woods, I was only using it at about 80 % full capacity. Air pressure was set at 80 % and the depth gauge was at 24. The only negative comment I have is the depth gauge should be marked with numbers to represent the depth. Here is a tip. The depth gauge is not marked on the nail gun. If you start from the lowest setting and count every click, there are a total of 30 clicks. I marked a line on the dial to give me an idea what the depth gauge is set at. That has worked perfectly for me and the nails have seated correctly every time. Over 400 nails into some dense thick wood and I haven’t had a single nail jam on me. Unbelievable power, incredible value, do yourself a favor and experience Christmas morning early this year.
April 18, 2013