Rated 2.0 out of 5 by 40
Rated 1.0 out of 5.0 by Russ Broke first time
First time using the #8 counter sink in pine board..... and it broke. Don't buy, stay away from Ryobi, it's all made in China garbage.
January 2, 2016
Rated 1.0 out of 5.0 by DstBstSN I should have checked the reviews first.
I lost another brand's version of a drill/countersink/driver at some point over the last year. I needed one, or something like it for a project so I headed down to Home Depot only to find they didn't stock the model I wanted. They had this Ryobi version, so I took a chance. Wish I would have read the reviews first. I agree, it's junk. Bits break like glass. It wobbles. The bit/driver gets stuck. Spend your money on something else.
March 16, 2013
Rated 5.0 out of 5.0 by Norm A must for a DIYer
On clearence and needed it for my use and toolbox.
February 25, 2015
Rated 1.0 out of 5.0 by Philbass04 Save your money
This unit was poorly thought out. Drill bit and shank are placed in drill chuck to drill pilot hole then collar slips over that to drill in screws. It makes for timely work but as you keep taking it apart and putting it together it eventually gets too much play and will not stay tight together making drilling almost impossible. I drilled about 50 holes until this $20 item was shot. Also allen wrench included is not correct size so when you go to tighten drill bit or change drill bit it will strip out the retaining screw.
April 15, 2014
Rated 1.0 out of 5.0 by crllc Waste of money
I was relunctant to purchase this product just because of the brand name but there were no other options available. The product was on the wrong hanger so I thought it was $4. When I first used it the bit stuck in the wood and pulled out of it's holder. I tightened the bit, drilled in the same hole and bit intact with the countersink came out of it's holder. There is no lock to hold it in place so every time you drill it comes out. I also looked for replacement bits, they have a flat side so the set screw holds them in place, but could not find them either.
July 1, 2013
Rated 1.0 out of 5.0 by nickname Do Not waste your $$
Within ONE hour... one drill bit broke and both phillips heads were stripped and unusable!!
I had the opposite dproblem of another person... i would drill the pilot hole in the wood, and as I tried to back it out, the shaft popped out, leaving the drill bit in the wood. I had to hand twist it out every time.
I had an older one that was all inclusive, no extra hex key, and had a 'locking' piece... what happened to that one? It lasted 8 years, it was awesome!
June 19, 2014
Rated 1.0 out of 5.0 by HJS Very bad design.
Badly designed. Pulls straight out like a four in one style screw driver, therefore after you countersink, the drill pulls out of the holder
No matter how you try avoid it from doing just that. Also Home Depot offers no replacement drills for it. I asked and was told by the section worker She could not order them.
But did not check to confirm it.I will be returning this product.
September 5, 2014
Rated 1.0 out of 5.0 by GBrown Snapped after 32 holes
Oh! I know to check the reviews, now. I would not have purchased this had I known so many others have had the same issue I had.
The bit is held by a very week magnet, if there is one there at all. So, it removed itself from the sleeve with every drill. Then the countersink-bit snapped after just 32 holes. I switched to the other countersink and I had to keep tightening the set screw after each drill. Absolute junk!
I was about to buy that fancy Ryobi Drill, but I'm glad I can change my mind on that.
October 17, 2013