Rated 4.5 out of 5 by 62
Rated 5.0 out of 5.0 by Chris Pex pipe is the way to go
Flexible, easy to install, no joints to worry about. Just cut to length and fit.
December 5, 2012
Rated 5.0 out of 5.0 by Auburn317 Great Product Easy To Use
I used SharkBite PEX to replace copper line running to my Water Heater. The red and blue colors make it easy to distinguish Hot and Cold lines after install is complete. Using a SharkBite coupling I easily transitioned from Copper to PEX, the PEX is more flexible than copper and easy to work with, it is also a great value at much lower price point. PEX is easy to cut as well and can be done with a PEX Cutter sold at Home Depot. Great product very easy to work with and use for an average DIYer.
May 20, 2014
Rated 1.0 out of 5.0 by SteveG CAUTION: very brittle
Sharkbite tubing is brittle and will break off (snap off) if flexed beyond it's (minimal) elastic limit. I used Sharkbite tubing purchased from HD for potable water in a new house on a concrete slab foundation. The Sharkbite tubing broke off (snapped off like a dry twig) flush with the concrete slab, even though it was properly shielded (per code) within a 3/4 flex conduit in the area where it emerged from the concrete slab. I have been forced to abandon Sharkbite tubing which was carefully placed under the slab, and install other tubing in the walls, above the slab. Plumbing contractor remarked that he would not use this tubing again.
March 19, 2015
Rated 5.0 out of 5.0 by Dale easy to use
I was going to use some copper piping I had on hand for a small job but I noticed that my HD also had 3' length of this available so I grabbed one of those and it made the whole job much easier and cheaper since I did not have to use two 90° elbows...
Such a simple system with Sharkbite fittings.
February 1, 2014
Rated 5.0 out of 5.0 by Adam Great Value
PEX is wonderful to work with. This Sharkbite brand pipe is flexible, good quality, and a great value for the money. I was able to install a new water line under my house at a fraction of a cost of hiring a plumber to do it. Even after the install, I still have A LOT of pipe left for future work/repairs. Just make sure to do your research and have the correct tools in place first before you work with PEX pipe.
August 6, 2014
Rated 5.0 out of 5.0 by Garrett Just re-piped my whole house with PEX
I discovered I had a slab leak on my hot water line under my bathroom and upon further investigation discovered a cold water leak under my entryway. Being in Ventura County, CA our water is hard and my tract home was made cheap. It was built 30 years ago with copper in the slab foundation. The plastic sheathing they used to isolate the copper from the concrete was super thin and subsequently eroded as the pipes expanded and contracted with temperature. This lead to major corrosion of the copper (especially in the hot water line) from the outside and the predominance of minerals in our hot water corroded the insides of the copper. I knew this would be a problem when I bought the house, as I have lived in the neighborhood for a while. Many neighbors have all had similar issues and paid big money to patch or re-pipe.
I am an avid DIY-er with just about every type of project. Electrical, plumbing, heating/AC, appliances, etc. I have patched and repaired many types of plumbing including copper, galvie, ABS, and PVC. I was new to PEX.
What I did:
I did a lot of research before making the purchase and weighed all of my options. I considered paying a plumber, doing it myself, using copper, and using PEX. I decided on PEX and wanted to do a manifold system so I can easily remodel my bathrooms in the future without turning off the whole house water supply. My house is a 1550sqft single-story house with 2 full bathrooms. I opted to replace the 1" copper line where it comes in to the garage from the shut-off valve outside and run it to the manifold location near the water heater. I split the 1" copper with a "T" and reduced it to 3/4" copper to the water heater supply and the cold-water side of the manifold. I used 3/4" SharkBite PEX stubs to feed into the manifold for a little flexibility. I ran 1/2" PEX to each fixture. I used red PEX for hot and blue PEX for cold. I wanted to reduce the amount of fitting and connectors in the system, but used 1/2" PEX to used copper stub-outs with new compression fitting valves to lead to each fixture; I didn't like the idea of the PEX sticking out of the walls. I used the stainless cinch-ring clips because the crimper is a bit smaller and fits in tighter spaces. I opted for the 100' rolls of the PEX so I could have a direct shot to each fixture without any unions along the way.
PEX, though flexible, is still fairly rigid and a bit tough to uncoil, but much better than copper. With a little patience and coercion, I was able to thread it through the headers and down the walls with minimal drywall cutting. I used 90-degree angle guides to protect the bends. Using the cinch rings at the connection points was easy. It took me 53 hours of work over the span of 4 days to complete the project (drywall repair included). It would have been a bit faster, but I had to cut a hole in part of my roof to access a header above the kitchen sink.
I am beyond thrilled with this product and how easy it was to install. I was able to re-pipe my entire house by myself in a few days for less than $1000. The copper portion alone cost me $300, so that puts the PEX at $700.
March 19, 2014
Rated 4.0 out of 5.0 by mcbonefive good product
if you get the 500 ft roll, make sure u have enough help....really difficult to work with, it was like playing with a 500ft spring.
February 12, 2015
Rated 5.0 out of 5.0 by TravisB A+ Product for Easy DIY Installation
Don't doubt yourself if you are thinking about a plumbing job with PEX. It's super easy. This product is way cheaper than copper and fittings are easy to complete. I am a financial advisor with no plumbing experience and I refit my whole house in a day. Two points to pay attention to: First, if you use copper rings, get the tool for the job, don't try and use the cheap crimper that uses vice grips close (and remember that it's hard to crimp in certain angles). Also, when you fit the PEX to your hot water supply, make sure that you don't have to keep some copper touching the unit, per your building codes. Other than that, super easy!!!
February 24, 2012