Rated 1.1 out of 5 by 12
Rated 1.0 out of 5.0 by Joe How-to guide for using this product
If you want your plumbing project to be successful with this product, follow these steps:
1) Open the package.
2) Throw the nuts in the garbage. The union piece is the only useful part.
3) Buy compression nuts with real ferrules.
4) Complete project in under 5 minutes instead of the 3 hours it took me to realize that no matter what I did, the included nut/ferrule combination would not seal.
July 27, 2015
Rated 1.0 out of 5.0 by STRAFF A Very Good Bad Design
What a piece of junk, I had a double union and a single, both leaked badly, there is no way to get the plastic tube past the rim of the c-fitting when tightening. I can't tell if the water is coming up between the plastic tube and brass collar or between the collar and the nut. Going back to the easy derlin sleeve and compression nut.
August 8, 2015
Rated 1.0 out of 5.0 by Greg same problem
Who knew you could get a compression fitting wrong!?!? Same problem as all others. It would not seal on the copper line. The 1/4" copper line that came with the refrigerator kit from Home Depot barely fit through so I thought I may have scratched the sleeve when inserting it. So I tried another one. Same problem. Glad I read the reviews as now I know not to try this again. I will go to lowes or another hardware store. Home Depot should really stop carrying this piece of junk if it is that bad. How hard is it to get a compression fitting that works?
May 1, 2014
Rated 1.0 out of 5.0 by denverhomeowner ugh
First, the description says compatible with other compression fittings. Not necessarily, there are some other brand fittings you cannot mix and match with. I found this out the while working on my roof, very inconvenient. If you're using this fitting, make sure you use its nut, sleeve, and ferrule together, not another brand sleeve etc.
Bigger problem is the integrated nut/sleeve. Might sound good since it reduces chance of losing the sleeve. But with plastic tubing with a ferrule properly inserted, it is virtually impossible to slide the integrated nut/sleeve over the tube/ferrel to the end. So I had to beat the nut / sleeve apart to separate the two pieces, not easy to do without damaging the sleeve. Then I could complete the installation, but even then it's not easy, that sleeve is a tight fit. In the end there were no leaks, but what a process.
Home Depot carries a Dial brand brass compression union that is sold as an accessory to evaporative coolers. It's half the cost of the Watts, I'm going to try it next.
May 26, 2014
Rated 1.0 out of 5.0 by saratoga Leak-Prone on Copper Tubing
Two couplings leaked at both ends when connecting copper tube for an icemaker. Torquing further did not help. The sleeve is such a tight fit on the tube that it scratches the tube surface. This is probably the leak path as the water comes out between the sleeve and the tube. Switched to the Watts flare union LFA-65 and A-60 flare nuts. Worked great.
July 12, 2014
Rated 1.0 out of 5.0 by handyandy what a waste of my time and money
Who would have thought to look at the reviews before you buy something as basic as this?
Wasted a lot of my time trying to get it to work. After deciding it wasn't going to work, I
questioned the design and came to look at the reviews. Comfirmed it wasn't me. I think
a simple piece of pipe with two basic compression fittings at both ends would have done it.
Will stay away from anything that looks like this in the future.
February 3, 2015
Rated 2.0 out of 5.0 Doesn't really work...
Used this fitting to attempt to transition from 1/4" copper tubing to an ice-maker line. This fitting seemed to fit the plastic tubing from the refrigerator just fine, but I couldn't get it to seal properly on the copper fitting. There are no compression rings (ferrules) on these fittings, just a pitiful excuse for a thin metal seal that is built into the cap nut, which I think is probably the problem. I'm glad these weren't expensive... sadly there are no alternative products at my local Home Depot, so I'll either have to try Lowe's or go to a mom-and-pop hardware store to find a decent product, I guess.
Long story short: avoid these cheesy fittings.
December 28, 2013
Rated 1.0 out of 5.0 by Karl Do Not Buy
Do your self a favor and go to a dedicated plumbing supply where you can get the union with caps with tappered inner diameter and the seperate ferule. The integrated ferule/cap design does not fit older 1/4" Tube and if you can manage to insert the tubing far enough, the fitting will not seal. These fitings are junk.
July 15, 2013