Rated 3.8 out of 5 by 24
Rated 1.0 out of 5.0 by Rick Nanopave Not Rainproof
Used this product on a patio area that has flagstone with crushed granite for mortor. The product was installed per instructions, drying period, mortor gap, crushed granite size and application rate. Initial this product functioned as manufacturer described for about two weeks. Then we got about two inches of rain over a week period. The product literally washed away and left zero hardness to the crushed granite mortor.
September 1, 2016
Rated 3.0 out of 5.0 by RDH Many hours , little results
We spent three days and over $200 sealing a patio and sidewalk. It washed out with the first heavy rain.
August 23, 2016
Rated 1.0 out of 5.0 by akaLA Very disappointed. Product was expensive with poor results.
This product did not work as I was told it would. It was purchased with the sand to use with flagstone and I was told that this product would harden and seal the sand around the flagstone. It was applied and given the recommended amount of time to dry and setup before foot traffic.
The sand did not ever harden and all of the sand is coming out from between the flagstone. Now we are going have to spend additional money to do something different.
August 9, 2016
Rated 4.0 out of 5.0 by Mikeb Works as advertised
I used this on top of regular paver sand to fill joints. I applied it during a warm summer day and it hardened by the night. You will have some weeds come through occasionally, but it's not bad. I preferred this over polymeric sand and I'm very happy with the decision.
August 16, 2016
Rated 3.0 out of 5.0 by Jugse Not strong enough for ants
Hardened as expected and sealed pavers pavers but ants tunneled through it within days.
August 9, 2016
Rated 5.0 out of 5.0 by BobSig Great Customer Service
I recently completed a review BobSig226 and describe the details of my experience. Since this review the manufacturer has stepped in to help rectify the situation with sealer not being compatible with jointing material. This review is to amend the original to a higher rating as a result of the manufacturer sending me another 5 gal supply of sealer to redo my walkway.
I still recommend that you test the sealer on the material you are sealing before a complete application.
July 16, 2016
Rated 1.0 out of 5.0 by BobSig Chunks flake off-not for all mixes
I originally purchased 2 gallons of Nanopave for my front steps. This application worked well for pavers with sand joints. I admit I used double the recommended application rate and got good results. At this point I probably would have given the product 4 stars. However, two weeks later I purchased the 5 gallon version for applying to my flagstone walkway with crushed limestone in joints. The container states an application rate double that of the sand joints. OK...so I even doubled this rate as an "insurance policy". The walkway looked great until I cut the grass and used leaf blower to blow grass off walkway. chunks of crushed stone started flying away. I then contacted Techsoil (makers of Nanopave) and they asked a bunch of questions. They are in the process of analyzing a sample of limestone mix from the quarry the mix was purchased from. According to the rep..."Their product should be tested before final use because it is not compatible with all mixes". Based on this statement, I should have gotten a sample from my landscaper prior to them installing the walkway, tested the sample with my $150 5 gallon Nanopave. And then when it didn't work, inform my landscaper they would have to use a different source for the joint mix only to start the testing process over again. BTW: The rep further stated that I would need to remove the joint mix and start over.For this, I give the product 1 star.
July 9, 2016
Rated 5.0 out of 5.0 by cueball9 The KING of paver sealents!
I did a lot of research on sealers and read all the posts online from guys who did all that work laying pavers only to have the sealer discolor the block!!
Lucky for me, my new wife had a paver patio installed just before we got married and the crew left behind a partial jug of this stuff.
You will NOT have any problems if you use this product to finish your paver project. It goes on easy and could not be simpler to use. Follow the instructions. I used a regular 2gal sprayer to apply and a straw broom to spread out. I used a squeegee on the first set.
Soaks into the sand quickly and dries HARD. I did heavy 2 coats. The sealer soaks into the block and disappears! NO DISCOLORATION!!! In fact, the "Ghost" product I used gives a very slight enhancement to the color but is NOT shiny.
FYI: I did do a comparison with a "Wet Look" product and did not care for the results. I did not want my pavers to look like polished marble!
This was my first time laying pavers and I am very pleased with the results. I got everything from HD and did my online research. Even after recent rains there is no washed out sand or lifting pavers etc. It's a backbreaking job to be sure and standing there ready to apply the sealer was very tense. The idea of pulling it all back up was unacceptable.
About an hour later I was happy and relieved!! Nano Pave works as promised!!
November 29, 2014