UltraTouch 48 in. x 75 in. Denim Insulation Hot Water Heater Blanket-60301-48752 at The Home Depot
Free shipping
Discontinued

UltraTouch

Model # 60301-48752

Internet # 202710039

48 in. x 75 in. Denim Insulation Hot Water Heater Blanket


UltraTouch 48 in. x 75 in. Denim Insulation Hot Water Heater Blanket
 

This item has been discontinued.
The Home Depot no longer carries this specific product.

$28.00 / each
Item cannot be shipped to the following state(s): AK,GU,HI,PR,VI

PRODUCT SOLD Online Only

In Stock

Loading...

PRODUCT OVERVIEW

Model # 60301-48752

Internet # 202710039

The UltraTouch Denim Insulation Water Heater Blanket improves the energy efficiency of your hot water heater with R6.7 performance. Helps maintain constant temperature and keeps the heat inside your unit.

  • Includes one 3 in. x 100 in. strip of tape for sealing the blanket closed
  • Made from 100% recycled denim and high performance foil
  • Quick and hassle free installation with non-itch denim insulating blanket
  • Fits most water heaters up to 60-Gal. capacity

Info & Guides

You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.

SPECIFICATIONS

Assembled Depth (in.)  2 in  Assembled Height (in.)  75 in 
Assembled Width (in.)  48 in  Coverage Area (sq. ft.)  25 
ENERGY STAR Certified  Yes  Formaldehyde Free  Yes 
Insulation Application Type  Garage  Insulation Type  Recycled Denim 
Product Length (ft.)  6.25 ft  Product Thickness (in.)  2 in 
Product Type  Blanket/Jacket  Product Weight (lb.)  6 lb 
R Value  6.7  Returnable  90-Day 
Roll or Batt  Roll  Vapor Retardent  No 
Warranty Information  1 Yr Limited Warranty 

CUSTOMER REVIEWS

Rated 4 out of 5 by 46 reviewers.
Rated 5 out of 5 by Heater Blankets I used these blankets to insulate my 18 foot wide by 8 foot high garage door. It was easy to cut and install (using Liquid nails) and has made about 10 degree difference in the internal temp. My door faces West and would reach 103 degrees in the late PM and temps in the garage were uncomfortable. Now they run just over 92 but with the 6000 BTU air con I can maintain temps around 89 with lo humidity. attic insulation is next. Door is much quieter now. July 3, 2013
Rated 5 out of 5 by easy to install Female diy'er. 40 gallon gas water heater, measured around then cut excess off the blanket. I had an extra roll of tape and used it. No problems so far. October 22, 2013
Rated 4 out of 5 by Keep it under wraps! Very easy to install and no fiberglass! So much thicker than I thought it was going to be and a perfect fit for the hot water heater. Barely any cutting was necessary and for the areas that had to be open (i.e. valves, temperature adjustment, wiring) the thickness was not a hinderance. Too soon to tell if it really will make a difference in the hot water bill (gas heater) but so far so good. October 1, 2013
Rated 3 out of 5 by Good product This is much better to work with than fiberglass. It gets a little dusty, but not like fiberglass dust. I love that it comes with the foil tape already in lengths. This made for an easy install. I didn't even need to cut it for my tank. It was fit to size. December 10, 2013
Rated 4 out of 5 by Does The Job There has been a significant reduction of heat leakge from the water heater. It is housed in a closet that used to get quite warm. This kit is the only one to buy if you do not want to spend a lot of time with itchy fiberglass. Expect to trim and cut and piece the right shape to do the job. Have extra foil tape on hand, you will need it. If you take your time it will work out well. May 1, 2012
2 3 4 5 6 >>

SHIPPING AND DELIVERY OPTIONS

Standard Shipping includes delivery by small parcel service. Processing time varies by product.


If product is eligible for shipping to AK, HI and US Territories additional transit time and remote surcharges may apply.