Rated 4.2 out of 5Â by 10
Rated 5 out of 5Â by sbrooks45 Lots of Power, well built
I had a 12 year old full sized Rigid that was seldom used, yet the 10 amp motor still burned up, very disappointing! This Makita is GREAT compared to the Rigid. Plenty of excess power (first job was ripping 2x4 on 38 deg angle, and it chewed through it no problem), light saw, but sturdy, very solid and well built. Other reviewers complained about the fence? I think the fence is great and it cut true out of the box (I did have to adjust the angle indicator on the blade though). I have had a really good track record with Makita motors, I down right abuse some of my older Makita saws, and they just keep running, so I'm sold on the Makita motor, as opposed to the Dewalt, Rigid, etc., that I just don't think are the highest quality and I seem to hear about them burning up more often. Bottom line, it was worth the extra $ for me to get the Makita.
June 21, 2012
Rated 5 out of 5Â by yzdeaner Best deal in town by far!
I researched this table saw for several weeks....read all the reviews about the Makita as well as other comparable saws. For me the key was the higher rpms that this saw delivers plus the Makita's motor IS NOT made in China. The blade arrived perfectly square but I did have to adjust the fence and the mitre to get a perfect cut. I also had to adjust the riving knife to align it perfectly behind the blade. I didn't mind the set up because it forced me to become familiar with the saw. The saw was over lubricated with petroleum jelly and that was a minor annoyance.
About the fence, it was easy to adjust and although it locks firm and square, it still can be moved if enough pressure is applied on the out feed end. A quick-grip clamp solves the problem.
The mitre fence had a small bit of play, which I eliminated by applying some duct tape on the bottom of the fence rail. It now slides smooth and has ZERO play.
I replaced the stock 32 tooth cross ripping blade with a full kerf 50 tooth Freud ATB blade (LU84M011) and have cut several hard woods with only a small drop in rpm, but no burning, binding or lights dimming in the shop. I cut some aged pressure treated 2 x 8s that were very dense and the saw performed well. So far that was the ultimate test. Granted, it was a brand new blade but my radial arm saw did not perform as well cutting the same wood.
One feature I really like is the brake on the blade when you turn of the power. It allows you to remove your cut wood without having to wait for the blade to stop rotating.....that's when a lot of accidents tend to happen.
The saw has a larger platform than most of its competitors, but I can still carry this saw relatively easily and I am age 56, and weight 168 pounds.
One complaint I can think of is the noise the saw makes at start up. It think it has something to do with the braking system disengaging, but it doesn't seem to be a problem other than the sound. During operation, the saw is less noisy than other saws I have used.
Overall, I am very satisfied with this portable saw. I feel it is a top of the line saw for a do-it-your-selfer and it you want more power you have to graduate up to a cabinet saw. At the price I purchased this saw I feel Home Depot deserves my attention more often. Thank you HD!
March 1, 2014
Rated 5 out of 5Â by circus621 Best saw yet
I bought this saw after having to return several others for fence alignment issues. I decided to spend the extra money to rid myself of the headaches of setting them up and returning the lesser brands. I'm so happy I did. this saw is quiet, strong and has the deepest cutting depth of its class. Definitely a good saw for the money.
September 6, 2013
Rated 5 out of 5Â by Bruce Worth every penny
Easy to assemble. Cuts true and much better than my old table saw. The table is the right size and the extension is simple to use. The rip fence is solid and simply to use. You won't be disappointed with this saw
May 22, 2012
Rated 4 out of 5Â by WCWHardwoodFloors Lasted 20+ Years
As a Hardwood Flooring contractor, I bought this 8" Makita table saw with plastic base, no metal legs in 1989, and still ripping! after using my bosses for over 10 years. Table saws are very dangerous tools. Always respect them, and think about your fingers before you turn it on. Prayer never hurts and may help focus the few brain cells we have left. . . . It's very important to have a sharp blade on your saw, primarily for safety, don't mess about with a dull blade, kick backs are far more likely and of course don't force the tool (aka feeding to fast). I've seen kick backs from 3/4" oak go right through a hollow core door. Don't try to rip wet lumber, it will bind and hurt you or something else. . . . Always stand to the side, not behind the blade and wear glasses and hearing protection (What?).
I bent/lost the angle indicator and a "helper" ran a skill saw across tho top inch+" of the fence but it still works well. I've replaced the brushes (under $10, in stock at good tool service type place) and lube the bottom (accessible) bearing, I could splurge and replace them, but it's likely more time and money than it's worth at this point and lubing them seems to really help, Thankfully it is not sealed, and it cuts much better with new brushes and lubed bearings (I actually only did the one that's accessible easily, sprayed the other one).
There is allot of resistance cranking it up and down with the small knob, so much that a bigger knob with a small handle would have likely broken. I've attempted to adjust the tension numerous times (easy to do with varied results) to some effect, as well as lubricate it as well. I've had to replace the original power cord with a heavy duty bright Yellow (12 gauge) extension cord (easier and cheaper than a factory part) as well as longer, eliminating the need for an extension cord 3/4 of the time.
The plastic base has broken, chipped and cracked to the point that i built a reinforcing frame for the bottom, which helps with stabilizing it as well as adding a bit of weight (ripped 2X4s). I don't think the factory legs are worth the time or money IMHO. Like all Makita (in my experience) tools it's loader than heck but it only bogs down with 3"+ miters on white oak making really thick custom thresholds, but otherwise it does just fine, especially ripping 5/16ths" and even 3/4" White oak quite well, if the blade is reasonably sharp. I'm starting to think the blade spray lube from Bostic is a good investment.
It has paid for itself likely a hundred times over. a good tool, likely a safe investment even used. Considering this is a circular saw on a fairly well engineered frame on a cheap base, it has exactly the power one would expect, or perhaps a bit more again, sharp blades make the difference.
I've had to learn to include blade cost and time into every third large job if i want to keep a sharp blade on it. Often it's faster/easier to just buy blades than ship them to the quite good, online blade sharpening outfits that guarantee their work. Ya just gotta have 10 blades in stock so you can rotate and make shipping them worth while, It's often good to buy two of the same tool so the blades/parts fit and on occasion I've even used a small miter saw blade on my table saw just because it was sharp and i didn't want to go buy a blade in the middle of the day, or i was feeling cheap, whatever, be careful!
May 23, 2013