Rated 4.6 out of 5Â by 57
Rated 5 out of 5Â by Brian Absolute necessity if you have to move your miter saw around a lot!
I bought this stand as a combo with the DWS780 miter saw and am very glad I did! I don't have a large shop so any time I need to do some work I have to lug my tools out and set them up, which can be tiring and time consuming. Miter saws are especially heavy and bulky, but it's usually the first tool I get out and the last one I put away. This stand will make me and my back much happier!
It was fairly straight forward to assemble as the instructions were pretty good. Usually, when I get anything that is beyond just a couple obvious parts, I will read the instructions and do exactly what they say just to see how "Dummy Proof" they are and these were pretty good. The only thing that I felt could have been clarified further was the axle assembly. If you've assembled these kind of axles before it is very straightforward and you won't bother with the instructions anyway, but if you haven't it could have been more helpful. The instructions basically said insert axle, mount wheel, tighten nut. Well, there are also 2 washers and a spacer that have to go on that aren't mentioned. Assembly order is axle, washer, spacer, wheel, washer, nut. As for the washers, there are 2 sides, one is slightly rough/flat and the other is rounded and smooth. When assembling the wheels, make sure the rounded/smooth sides are facing the wheels. If the other side is facing the wheels they will dig into the plastic and you'll get yellow shavings on the floor. I highly doubt it will do any real permanent damage to the wheels, but it's a simple thing to flip a washer and never think about it again.
As for usability, can't beat it! It collapses and raises up without any fear of it slamming down to the ground if you accidentally let go. It is very sturdy once up and the outriggers work great. There are 2 heights that it will stop at, but I really have no use for the shortest one as I am usually standing up while I'm working and it's just too short. It does still take a little strength to get it all the way up with a 60lbs miter saw on top, but it's nothing like dead lifting the saw by itself off the ground.
I would highly recommend this no matter what brand miter saw you've got! As adjustable as the mounts are on the stand, the base of your saw would have to be incredibly large to not fit. I've got the DWS780 on it and still had 3" more front to back as well as around 8" of side to side space left.
March 20, 2013
Rated 5 out of 5Â by MRJEG A MUST HAVE
This stand is a must have for a miter saw. If you are like me I need all the space in my garage so portability is a must. It allows me to store miter saw easily then take out of garage easily when working on a project. Assembly was took longer than should have because of the instructions provided. The quality of the stand is awesome. Wheels have rubber and are not like cheap plastic. The stand comes with a shock to ease lifting and folding down.
July 28, 2013
Rated 4 out of 5Â by RJRR Excellent stand despite a few minor issues
Picked up the DWX726 to hold my new DWS780 slider. The stand is sturdy and overall well built. The ease to lift and lower is exactly what I was looking for. The portability is great, the support/feed rollers adjust perfectly and easily hold 8' long 2x4 and 4x4's with no sagging.
The only negatives were that two of the screw holes were very easily stripped during assembly. One of the M6 attaching the wheel supports and the small M6 on the handle. I simply retapped the leg hole to a 3/8-24 and drilled out the handle home and put a 1.5" 1/4-20 bolt with lock nut in it's place. I would be better if DeWalt had used through holes with bolts/nuts vs. the poor self tapped holes.
September 9, 2013
Rated 4 out of 5Â by Devastator Must for any large Miter saw owner
The directions were not good for putting this together, but the pieces all make sense so it was not too tough to put together without the instructions. When it is all the way up or all the way down there is some resistance when trying to lift or lower it. At first I thought if I pulled it up any harder it would break. Now that I am used to it, I have no trouble. You just push the lever and pull really hard and up it pops. There is a hydraulic assist that helps you lift the saw but it helps the most in the middle of the range of motion so the very top and very bottom do not have as much hydraulic assistance. Again now that I am used to it I know you just give it a good hard pull to start the motion and then it does the rest. Those are pretty minor complaints and now that I am used to it they are not really complaints. The rest of the features are great. It has 2 options for how tall to make the stand. The rollers on either side of the work area are great. The saw mounting bolts have very many options, my saw mounting bolts are not in a perfect square, and it was still very easy to mount it to the stand. I was able to mount the saw so the weight was centered on the stand. It is really cool that when the saw is lowered the stand acts as a dolly to make moving a big heavy saw much easier. I think this should be a 4.5 star rating but that is not an option. If the hydraulic assist was smoother all the way through the range of motion it would be 5 stars so that is the reason for the 1/2 star deduction.
August 5, 2014
Rated 4 out of 5Â by Noname Good Tool to Have Except,
Dewalt Needs to redesign the handle used for raing and lowering the table ,It doesnt fit flush and the screw used should be a machine screw and nut not a screw that screws into the base.The Only other improvement I would like to see is a better way to raise and lower the table,Once you get the feel for how to to it,Its not bad at all.Ihave used Mine several times and find it a nice addition to the saw
September 3, 2014